manualshive.com logo in svg

TPS WP-81, Руководство пользователя, Страница: 20 / 51

Поделиться
Скачать
TPS WP-81 Скачать руководство пользователя страница 20

 

Page 20 

7.3  Calibration Messages 

1.  If  a  temperature  calibration  has  been  successfully  performed,  the  

WP-81

  will  display  the  following  message  and  the  offset  value  of  the 

sensor

. For example… 

Calibrate OK 
Offset=  1.0

o

c 

2.  If  a  temperature  calibration  has  failed,  the 

WP-81

  will  display  the 

following message, and the failed offset value of the sensor. 

Calibrate Fail 
Offset=  10.5

o

c 

7.4  Manual Temperature Setting 

If  the  Conductivity/Temperature  sensor  is  not  connected,  and  a 
temperature sensor is not used in its place, the temperature of the sample 
solution must be set manually for accurate pH measurements. A separate 
thermometer will be required for this. 

NOTE:

  The  Conductivity  sensor  has  a  separate  sensor  built  in  for 

automatic  temperature  compensation  for  Conductivity,  TDS  and 
Salinity. 

1.  Switch the meter on. 

2.  Measure the temperature of the sample. 

3.  Select Temperature Calibration. ( 

 

 

F1:Cal. 

 

F3:Temp

) 

4.  The current temperature setting is now displayed. 

 25.0

 Man Temp 



:Set   F1:Save

 

5.  Press the 

 and 

 keys until the display shows the temperature of 

the sample. 

6.  Press the 

 key to save the temperature value. 

Alternatively, press the 

 key to quit and retain the current setting. 

Содержание WP-81




















































Отзывы:

Нет отзывов