TPM 207-D533-NN Скачать руководство пользователя страница 41

Страница: 41 / 46

TPM

207-D533-NN User Manual

6.1.1

Device Addressing

The device can be addressed via Device Position Address (Auto Increment address), by Node Address

(Configured Station Address/Configured Station Alias), or by a Broadcast.

⚫

Position Addressing (Auto-Increment Addressing)

In this mode, the datagram holds the position address of the addressed slave as a negative value. Each slave

increments the address. The slave which reads the address equal zero is addressed and will execute the

appropriate command at receives.

Position Addressing should only be used during starting

up of the EtherCAT system to scan the fieldbus and

later only occasionally to detect newly attached slaves.

⚫

Node Addressing (Fixed Addressing)

The configured Station Address is assigned by the master during start

up and cannot be changed by the

EtherCAT slave. The Configured Station Alias address is stored in the ESI EEPROM. The Configured Station

Alias must be enabled by the master. The appropriate command action will be executed if Node Address

matches with either Configured Station Address or Configured Station Alias.

The slave matched to the address set at station register (0x0010) from the master by position addressing is

normally addressed in node addressing. This enables access without fail even when a device is added, the

segment topology has changed and/or the slave has been removed.

The respective slave node address is set with the dip switch at the front of the device and CoE Object dictionary

4000h. 0 - 65535 axes addresses can be set using the 8 dip switch (0x00 - 0xFF:bit7 - 0) at the front of the

device and with a set value of bit 15 – 8, previously written in the non-volatile memory (4000h:02h) inside the

device. When the alias selection (4000h:01h) is set to 1, the setting values will be written in the station alias

setting register (0x0012) in an address space after the control power has been turned ON. When the device

address has changed under the control power ON status, re-input the power to enable the change in axis address.

Содержание 207-D533-NN















































Результаты поиска

Содержание 207-D533-NN

Отзывы:

Похожие инструкции для 207-D533-NN

Бренды по названию

Популярные бренды

TPM 207-D533-NN, Руководство пользователя

Результаты поиска

Содержание 207-D533-NN

Отзывы:

Похожие инструкции для 207-D533-NN

Бренды по названию

Популярные бренды