TP-Link omada OC200 Скачать руководство пользователя страница 67

Страница: 67 / 117

3.1

Monitor the EAP

To monitor the EAP information, go to the

Status

Device

page.

The following device information is displayed:

Device Name

Displays the name of the EAP. The name consists of the product model

followed with the MAC address of the EAP by default.

Device Model

Displays the product model of the EAP.

Firmware Version

Displays the current firmware version the EAP. To update the firmware,
you can refer to

5.6 Update the Firmware

Hardware Version

Displays the hardware version the EAP.

MAC Address

Displays the MAC address of the EAP.

IP Address

Displays the IP address of the EAP.

Subnet Mask

Displays the subnet mask of the EAP.

System Time

Displays the current system time. To configure the system time, you can
refer to

5.3 Configure the System Time

Uptime

Displays how long the EAP has been working since it starts up.

Содержание omada OC200






















































































































Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды

TP-Link omada OC200, Руководство пользователя

Результаты поиска

Содержание omada OC200

Отзывы:

Похожие инструкции для omada OC200

Бренды по названию

Популярные бренды