TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 69

Страница: 69 / 80

Disassembly and Disposal

TOX_Manual_Powerpackage_line-Q_en

12 Disassembly and Disposal

12.1

Safety during disassembly and disposal

DANGER

Electrical hazards in case of contact with live parts!

Electric shock, burns or death in case of contact with live parts!

Have all work on the electrical equipment performed by an electrician.

Disconnect power supply.

Wait for residual energy to disspate safely (at least 3 minutes).

WARNING

Ejecting parts and compressed air from compressed air conducting
lines!

Serious injuries to eyes and body cavities!

Always connect and disconnect lines without pressure.

Pay attention to maximum permitted pressures.

Wear individual protective equipment.

CAUTION

Sharp edges caused by material splintering!

Injuries from worn parts!

Wear individual protective equipment.

Do not move fingers along the cutting edges.

Be particularly careful and attentive.

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 69 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: