TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 57

Страница: 57 / 80

Maintenance

TOX_Manual_Powerpackage_line-Q_en

10 Maintenance

10.1

Safety during maintenance

DANGER

Electrical hazards in case of contact with live parts!

Electric shock, burns or death in case of contact with live parts!

Have all work on the electrical equipment performed by an electrician.

Disconnect power supply.

Wait for residual energy to disspate safely (at least 3 minutes).

WARNING

Hot surfaces on the drive and on the control box!

Injuries from burns!

Allow hot surfaces and motors to cool down before touching them.

WARNING

Ejecting parts and compressed air from compressed air conducting
lines!

Serious injuries to eyes and body cavities!

Always connect and disconnect lines without pressure.

Pay attention to maximum permitted pressures.

Wear individual protective equipment.

WARNING

Dangerous machine movements!

Serious contusions and injuries!

Make sure that that no persons are located in the danger area during
operation.

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 57 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: