TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 27

Страница: 27 / 80

Installation

TOX_Manual_Powerpackage_line-Q_en

6 Installation

6.1

Safety during installation

The installation may only be carried out by trained and authorized person-
nel.

DANGER

Electrical hazards in case of contact with live parts!

Electric shock, burns or death in case of contact with live parts!

Have all work on the electrical equipment performed by an electrician.

Disconnect power supply.

Wait for residual energy to disspate safely (at least 3 minutes).

WARNING

Ejecting parts and compressed air from compressed air conducting
lines!

Serious injuries to eyes and body cavities!

Always connect and disconnect lines without pressure.

Pay attention to maximum permitted pressures.

Wear individual protective equipment.

CAUTION

Tripping points from laid supply lines!

Injuries from tripping and falling!

Avoid tripping points when setting up.

Mark unavoidable tripping points with warning sign.

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 27 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: