TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 26

Страница: 26 / 80

Transport and storage

TOX_Manual_Powerpackage_line-Q_en

5.2

Lifting device

Depending on the size of the drive, the flange cover at the rear is provided
with threaded bore holes for ring bolts for hoisting.

WARNING

Risk of impact and crushing due to products swivelling out!

Severe impacts, crushing, and serious accidents as a result of the product
rotating and swiveling out.

Pay attention to the center of gravity and pivot point.

Establish a V-shaped suspension connection in the center of gravity
between the ring bolts.

If there are no threaded holes, suspend the ring bolt between the work-
ing part and intensifier.

Lift up the product carefully.

5.3

Temporary storages

Use original packaging.

Make sure that all connections and threads are covered to prevent dust
ingress and shocks.

Store the product only in closed, dry, dust-free and dirt-free rooms at
room temperature.

5.4

Dispatch for repair

If the device is sent to TOX

PRESSOTECHNIK for repair, the following in-

formation is required:

Detailed description of the fault

Operating conditions and installations e.g. upstream devices, etc.

Contact person at TOX

PRESSOTECHNIK

Contact person at your company in case of questions

For additional information and forms see

http://www.tox-pressotechnik.com/

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 26 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: