TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 19

Страница: 19 / 80

About this product

TOX_Manual_Powerpackage_line-Q_en

3.4

Product overview of Powerpackage line-Q

Working piston

Compressed air supply return stroke [2]

Control throttle 'X'

Compressed air supply fast approach
stroke [4]

Oil filling nipple

Power stroke valve

Fig. 1

Product overview type Q-S, Q-K

For product versions and product attributes see the design and installation
guideline.

3.4.1

Product attributes of Powerpackage line-Q

Type Q-S

Type Q-K

Intensifier and working part are interconnected with
a tension rod in a sandwich construction.

Intensifier and working part are connected with an
intermediate flange (compact construction).

Including power stroke valve and control throttle 'X'.

Equipped with mechanical spring.

Including power bypass ZLB with hydraulic end position cushioning ZHD in the upper final position.

Including fixed stop with elastomer cushioning in the lower final position.

Prepared for stroke monitoring ZHU.

Prepared for external linear position sensor ZHW.

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 19 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: