Tower Hobbies Tower Trainer 40 Ready-to-Fly Скачать руководство пользователя | Manualshive

Страница: 1 / 12

background image

Tower Trainer

™

40 Ready-to-Fly

RADIO CONTROLLED MODEL AIRPLANE

WARRANTY

Tower Hobbies

®

guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or modification.

In no case shall Tower Hobbies’ liability exceed the original

cost of the purchased kit. Further, Tower Hobbies reserves the right to change or modify this warranty without notice.

In that Tower Hobbies has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit
immediately in new and unused condition to the place of purchase.

© Copyright 2002 V1.0

TOWZ1154 for TOWA21**

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND
WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

1
2
3
...
»

Содержание Tower Trainer 40 Ready-to-Fly













Отзывы:

Нет отзывов

Похожие инструкции для Tower Trainer 40 Ready-to-Fly

Бренд: Badger Basket Страницы: 3

Бренд: Badger Basket Страницы: 4

Бренд: Badger Basket Страницы: 10

Бренд: Badger Basket Страницы: 6

Бренд: Jamara Страницы: 4

Бренд: Jamara Страницы: 8

Бренд: Old School Model Works Страницы: 20

Бренд: Little Tikes Страницы: 28

Bubble Dinosaur

Бренд: AbleNet Страницы: 8

Бренд: Vollmer Страницы: 5

Clickables Fairy Charms IM-21300B

Бренд: Techno Source Страницы: 1

CAR SYSTEM CONVERSION CHASSIS LORRY MB CITARO 162034

Бренд: Faller Страницы: 2

Бренд: Faller Страницы: 12

B-17E/F engines

Бренд: Eduard Страницы: 2

0067 85006700200

Бренд: Monogram Страницы: 33

Бренд: Ripmax Страницы: 12

Radio Control Pterodactyl

Бренд: Toysrus Страницы: 2

Бренд: Mega Bloks Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды