LCM 1010 Instruction Manual
2 SAFETY
2.4.2
Access Procedures for Dangerous Areas
Access each dangerous area with the corresponding procedure as follows.
NOTE
The procedure below is for use with four Press modules
(Semi-Automatic).
Access Procedure for Dangerous Area 1
- When an operator needs to access inside o f the door, follow the procedure below:
^
(1) Stop machine operation. ,
(2) Open the press front door, and access the press unit.
(3) To access inside o f the press unit, use thorbugh caution in the up/down
^operation o f thec slide platen. Do not touch a button on the press operation
panel carelessly. (If it is necessaiy to access the press when the mold die is
still hot, wear clothes with long sleeves and heat-resistant gloves, and use
caution not to touch a hot surface.)
Access Procedure for Dangerous Area 2
- When an operator needs to access inside o f the door, follow the procedure below:
(1) Stop machine operation.
(2) Open the press front door, and access the press unit.
(3) To access inside o f the press unit, use thorough caution in the up/down
operation o f the slide platen. Do not touch a button on the press operation
panel carelessly. (If it is necessaiy to access the press when the mold die is
still hot, wear clothes with long sleeves and heat-resistant gloves, and use
caution not to touch a hot surface.)
- When entering this door, pay sufficient attentiojito the traveling movement o f the
Release Film Handler Unit and to other partsThat can move.
- When entering this door, pay sufficient athm tioh’to the traveling movement o f the
Dispenser Unit and to other parts that can move.;-'
3
<3
-
J
Access Procedure for Dangerous Area 3
- When entering this door, pay sufficient attention to the traveling movement o f the
Dispenser Unit and to other parts that can move.
Access Procedure for Dangerous Area 4
- Operators are forbidden access within any doors. I f an occasion arises when
internal work is necessary, please leave such work to the maintenance engineers.
- Before entering the control box, be sure to cut off the power source.
- When entering the control box, be sure to wear gloves and keep hands and fingers
away from live parts inside control. (It is necessary for the electrical discharge o f
the electricity accumulated for five minutes or m o re.)
TCWA
2-25
Содержание LCM1010
