background image

102

Mobile Computing

Monitoring main battery power

The above error message may vary by computer model.

The RTC battery does not charge while the computer is turned off 
even when the AC adaptor is charging the computer. The RTC battery 
charges when the computer is powered on.

If the RTC battery is low, the real-time clock and calendar may 
display the incorrect time and date, or stop working.

To recharge the RTC battery, plug the computer into a live electrical 
outlet and leave the computer powered on for 24 hours.

It is seldom necessary to charge the RTC battery because it charges 
while the computer is on. If the RTC battery is low, the real-time 
clock and calendar may display the incorrect time and date or stop 
working.

When Hibernation mode is enabled and the RTC battery is 
completely discharged, a warning prompts you to reset the real-time 
clock.

The computer can be used while the RTC battery is being charged, 
although the charging status of the RTC battery cannot be 
monitored.

Monitoring main battery power

The computer’s main battery light gives you an indication of the 
main battery’s current charge. The following also applies to the 
secondary battery (available on certain models) if installed.

Glows amber while the main battery is being charged (AC 
adaptor connected).

Glows green when the main battery is fully charged.

Is unlit when the battery has discharged, the battery is not 
charging, or the AC adaptor is not plugged into the computer or 
AC outlet.

NOTE

NOTE

Содержание Satellite L40













































































































































































































Отзывы: