manualshive.com logo in svg

Toshiba RBC-U33P-E, Руководство по установке, Страница: 6 / 7

Поделиться
Скачать
Toshiba RBC-U33P-E Скачать руководство пользователя страница 6

- 6 -

Installation of air inlet grille

•  Install the air inlet grille in the reverse procedure of the removal.
•  Be sure not to pinch the louver motor wiring to install the air inlet grille.
•  Attach a Safety strap hook of the air inlet grille to the ceiling panel.

Hook hole of 
ceiling panel

Safety strap hook

3. Louver operation set up

REQUIREMENT

•  Use the wired remote controller to change the setting.
•  The setting cannot be changed using the wireless remote controller, sub remote controller, or remote-controller-less system 

(for central remote controller only). Therefore, installs the wired remote controller to change the settings.

 

CAUTION

Set only the CODE No. shown in the following table: DO NOT set any other CODE No.
If a CODE No. not listed is set, it may not be possible to operate the air conditioner or other trouble with the product may 
result.

1.  Turn the power on.
2.  Push and hold   +   +   buttons simultaneously for 4 seconds or more. After a while the display flashes.
 

Confirm that CODE No. is [10]. Also, the fan of the selected unit runs and the louvers start swing.

• 

If the CODE No. is not [10], push   button to clear the display content, and repeat the procedure from the beginning

3.  Select an indoor unit to be set by pushing 

 button (Left side of the button). Indoor unit No. changes each time the 

button is pushed.

4.  Change the CODE No. to [47] with 

 buttons.

5.  Set the (SET DATA) like as the following table with 

TIME

 buttons.

6. Push   button. The display state changes from flashing to lighting, and the setting is fixed.
7.  Continue set the CODE No. [48] ~ [4E] like as the table with repeat procedure (4) - (6).

• 

To change setting of another indoor unit, repeat from procedure (3)

8.  When settings have been complete, push   button to determine the settings.

• 

When   button is pushed, 

 

flashes and then the display content disappears and the air conditioner enters the 

normal stop mode. (While 

 

 

 is flashing, no operation of the remote controller is accepted.)

CODE No.

SET DATA

47

0024

48

0024

49

0030

4A

0035

4B

0040

4C

0043

4D

0046

4E

0060

4 8 6 2

5 3

<RBC-AMT32E>

Содержание RBC-U33P-E








Отзывы:

Нет отзывов