Toshiba RAS-18PAVSG-E Скачать руководство пользователя страница 62

Страница: 62 / 137

-3. Indoor Unit

-3-1. Installation place

CAUTION

•

Direct sunlight to the indoor unit’s wireless

receiver should be avoided.

•

The microprocessor in the indoor unit should not

be too close to RF noise sources.

(For details, see the owner’s manual.)

<Remote control>

•

A place where there are no obstacles such as a

curtain that may block the signal from the indoor

unit.

•

Do not install the remote control in a place exposed

to direct sunlight or close to a heating source, such

as a stove.

•

Keep the remote control at least 1 m apart from the

nearest TV set or stereo equipment. (This is

necessary to prevent image disturbances or noise

interference.)

•

The location of the remote control should be

determined as shown below.

Fig. 10-3-1

(Top view)

Indoor unit

Reception

range

Reception

range

Remote

control

(Side view)

Indoor

unit

10-3-2. Cutting a hole and mounting installation

<Cutting a hole>

When installing the refrigerant pipes from the rear.

1. After determining the pipe hole position on the

mounting plate (

), drill the pipe hole (

∅

65 mm) at

a slight downward slant to the outdoor side.

NOTE

•

When drilling a wall that contains a metal lath, wire

lath or metal plate, be sure to use a pipe hole brim

ring sold separately.

<Mounting the installation plate>

Fig. 10-3-3

Fig. 10-3-2

Remote

• A place which provides the spaces around the

indoor unit as shown in the diagram

• A place where there are no obstacles near the air

inlet and outlet

•

•
•

A place which allows easy installation of the piping

to the outdoor unit

A place which allows the front panel to be opened

The indoor unit shall be installed at least 2.5 m height.

Also, it must avoided to put anything on the top of the

indoor unit.

m from the right side edge is

e center of pipe hole

120

180

240

The center of the pipe hole

is above the arrow.

Pipe hole

Ø65 mm

23 mm

Hook

Pipe hole

Installation plate

Mounting

screw

Weight

Indoor unit

Thread

Anchor bolt holes

170

132

65 mm

300

FILE NO. SVM-17001

- 62 -

Содержание RAS-18PAVSG-E










































































































































Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы:

Toshiba RAS-18PAVSG-E, Руководство по обслуживанию, Страница: 62 / 137

Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы: