Toshiba RAS-18PAVSG-E Скачать руководство пользователя страница 41

Страница: 41 / 137

Item

8. Louver control

1) Louver

position

Operation flow and applicable data, etc.

This function controls the air direction of the indoor unit.

Description

•

The position is automatically controlled according to the operation

•

The set louver position is stored in memory by the microcomputer,

The angle of the louver is indicated as the louver closes fully is 0°.

mode (COOL/HEAT).

and the louver returns to the stored position when the next operation
is performed. (Cooling/Heating memory position)

1) Louver position in cooling operation

Wide air direction

Wide-angle

Right wide

Left wide

Spot air direction

Spot front

Spot right

Spot left

Initial setting of "Cooling storage position"

Louver : Directs downward (40.9°)

FILE NO. SVM-17001

- 41 -

Содержание RAS-18PAVSG-E










































































































































Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы:

Toshiba RAS-18PAVSG-E, Руководство по обслуживанию, Страница: 41 / 137

Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы: