Toshiba RAS-18PAVSG-E Скачать руководство пользователя страница 37

Страница: 37 / 137

Item

3. Outdoor fan

motor control

Operation flow and applicable data, etc.

The blowing air volume at the outdoor unit side is controlled.
Receiving the operation command from the controller of

indoor unit, the controller of outdoor unit controls fan speed.
* For the fan motor, a DC motor with non-stage variable

speed system is used. However, it is limited to 8 stages for

reasons of controlling.

Description

1) The operation command sent

from the remote controller is

processed by the indoor unit

controller and transferred to the

controller of the outdoor unit.

2) When strong wind blows at

outdoor side, the operation of air

conditioner continues with the

fan motor stopped.

3) Whether the fan is locked or not

is detected, and the operation of

air conditioner stops and an

alarm is displayed if the fan is

locked.

4) According to each operation

mode, by the conditions of

outdoor temperature (To) and

compressor revolution, the speed

of the outdoor fan shown in the

table is selected.

Air conditioner ON

(Remote controller)

YES

Indoor unit controller

Fan motor ON

3) Fan lock

4) Motor operates as shown in the table below.

1) Outdoor unit

operation command

(Outdoor fan control)

Air conditioner

OFF

Alarm

display

2) Fan speed

≥

400.

(by strong wind)

when the motor OFF.

Fan motor OFF continues

(Use wind for heat

exchanging)

30.6≤Hz

RAS-24PAVSG-E

Hz<13.8

13.8≤Hz<32.4

32.4≤Hz

MIN

MAX

MIN

MAX

MIN

MAX

When To is abnormal

OFF

To≥5.5 °C

To≥0 °C
To<0 °C

Compressor speed (rps)

In cooling operation

To≥38 °C
To≥28 °C
To≥15 °C

Model

RAS-18PAVSG-E

Hz<13.8

RAS-22PAVSG-E

13.8≤Hz<30.6

Tap

RAS-18PKVSG-E

RAS-22PKVSG-E

RAS-24PKVSG-E

200

250

300

350

360

450

440

500

560

550

600

650

RPM

Tap

RAS-18PKVSG-E

RAS-22PKVSG-E

RAS-24PKVSG-E

650

700

750

700

750

800

750

800

850

750

900

950

900

950

900

RPM

Outdoor fan speed (rpm)

FILE NO. SVM-17001

- 37 -

Содержание RAS-18PAVSG-E










































































































































Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы:

Toshiba RAS-18PAVSG-E, Руководство по обслуживанию, Страница: 37 / 137

Результаты поиска

Содержание RAS-18PAVSG-E

Отзывы: