Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 76

Страница: 76 / 333

– 76 –

NO.

Item

Specification outline

Remarks

8 Cooling oil

(refrigerant)

recovery

control

While the outdoor unit is recovering cooling oil (refrigerant), the indoor units perform

the following control tasks:
[common for operational (cooling thermo ON / thermo OFF / FAN), as well as

nonoperational indoor units]

1) Open the indoor PMV to a certain degree.
2) Engage in recovery control for a specified period of time and return to normal

cooling operation at the end of this period upon terminating the control.

3) Operate the drain pump throughout the recovery control period and for about 1

minute after it.

• Recovery operation

normally takes

place roughly every

2 hours.

• The opening

position of the

indoor PMV

depending on the

type and capacity

of the indoor unit.

9 Heating

refrigerant (oil)

recovery

control

While the outdoor unit is recovering heating refrigerant (oil), the indoor units perform

the following control tasks:

1) Open the indoor PMV to a certain degree.
2) Control the indoor fan according to the operation mode.

[Indoor units operating in heating thermo ON/OFF state]

Let the indoor fan continue operating, but turn it off if the temperature of the indoor

heat exchanger drops.

[Indoor units operating in FAN mode]

Turn off the indoor fan and display “HEATING STANDBY

” on the remote

controller.

[Non-operational indoor units]

Keep the indoor fan turned off.
3) Terminate the recovery operation depending on the TC2 temperature reading.

The timing of termination is determined by each indoor unit.

4) Operate the indoor fan and drain pump for about 1 minute after the termination

of the recovery operation. (Applicable to 4-way cassette type, 2-way cassette

type and 1-way cassette type)

• Recovery

operation

normally takes

place roughly

every hour.

• The opening

position of the

indoor PMV

depending on the

type and capacity

of the indoor unit.

10 Defrosting

control

While the outdoor unit is engaged in defrosting control, the indoor units perform the

following control tasks:

1) Open the indoor PMV to a certain degree.
2) Control the indoor fan according to the operation mode.

[Indoor units operating in heating thermo ON/OFF state]

Let the indoor fan continue operating for a while, but turn it off as the temperature

of the indoor heat exchanger drops.

[Indoor units operating in FAN mode]

Let the indoor fan continue operating.

[Non-operational indoor units]

Keep the indoor fan turned off.
3) As defrosting control comes to an end, it gives way to heating refrigerant (oil)

recovery control.

(For control details, see “9. Heating refrigerant (oil) recovery control” above.)

• For defrosting

commencement

conditions, see

item of outdoor

unit, “7.

Defrosting control

(reverse defrosting

method)” above.

• The opening

position of the

indoor PMV

depending on the

type and capacity

11 Short

intermittent

operation

compensation

control

1. For 5 minutes after startup, the system is forced to continue operating even if it

reaches the thermo OFF region.

2. However, priority is given to cooling/heating selection, operation standby, and

protective control, so that there is no overriding of thermo OFF in these cases.

12 Drain pump

control

1. During cooling (including DRY operation), the drain pump is operated at all times.
2. If the float switch is activated while the drain pump is in operation, the drain pump

continues operating, with the relevant check code displayed.

3. If the float switch is activated while the drain pump is turned off, thermo OFF is

forced on the air conditioner, with the drain pump put into operation. If the float

switch continues to be activated for about 5 minutes, the drain pump is turned off,

with the relevant check code displayed.

Check code [P10]

13 Elimination of

residual heat

1. When the air conditioner is turned off after engaging in heating operation, the

indoor fan is operated for about 30 seconds in “breeze” mode.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 76 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: