manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 43 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 43

– 43 –

(1) The dotted line represents a wire procured locally, and the dashed line represents an option sold

separately.

(2)

 represents a terminal block, 

 represents a connection terminal, 

 represents a connector on

the printed circuit board and 

 represents a short circuit connector.

(3)  represents a protective earth.
(4)

 represents a printed circuit board.

(5) Using a no voltage a-contact input of the external input (option), the following operations are available.

Between 1 and 2 : Selecting the remote controller operation (Invalid / Valid)

Between 1 and 3 : Adjusting the fan speed (Low / High)

Between 1 and 5 : Operation (ON / OFF)

Use a microcurrent contact (DC 12 V, 1 mA). In addition, ON / OFF operation is possible when using a

voltage of DC 12 V or 24 V.

(6) Orange wire (High) is connected as factory default. To switch to “Extra High”, connect black wire's

connector instead of orange.

Code

Parts name

Code

Parts name

Code

Parts name

CN**

Connector

TFA

TFA sensor

DMV1

Decompression magnetic valve

F01

Fuse (printed circuit board)

TCJ, TC1, TC2 Indoor coil sensor

PMV

Pulse modulating valve

F02

Fuse (motor)

TB1

Terminal block (power source)

SW701

Dip switch

FM1

Air supplying motor

TB2

Terminal block (communication)

43F11, 43F12

Relay for air supplying motor

FM2

Air exhausting motor

TB3

Terminal block (external output)

43F21, 43F22

Relay for air exhausting motor

DAM

Damper motor

TB4

Terminal block (humidistat)

RY701, RY702 Relay for air supplying motor

TRA

TRA sensor

TB5

Terminal block (magnetic valve)

RY704, RY705 Relay for air exhausting motor

TOA

TOA sensor

FS1

Float switch

TSA

TSA sensor

MV1

Magnetic valve

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов