manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 288 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 288

– 288 –

(6) Set the dip switch (SW800) setting of the service board to match the switch setting from the original PCB.

- Set the dip switch (SW800) depending on the position of the IPDU within the electrical box, as shown in

the following diagram.

ON

3

4

2

1

ON

3

4

2

1

ON

3

4

2

1

ON OFF OFF OFF

ON

3

4

2

1

OFF ON OFF OFF

ON

3

4

2

1

ON ON OFF OFF

Dip Switch

(SW800)

Ex. MMY-MAP1004FT8

Ex. MMY-MAP1604FT8

Compressor IPDU [Left Side]

For Compressor: 1

Dip switch (SW800) setting:

Compressor IPDU [Right Side]

For Compressor: 2

Dip switch (SW800) setting:

Compressor IPDU [Left Side]

For Compressor: 1

Dip switch (SW800) setting:

Compressor IPDU [Middle]

For Compressor: 2

Dip switch (SW800) setting:

Compressor IPDU [Right Side]

For Compressor: 3

Dip switch (SW800) setting:

ON OFF OFF OFF

OFF ON OFF OFF

(7) Align the heat sink with the screw holes on the heat sink and the mounting holes on the PCB with the PCB

mounts. And fix the Compressor IPDU to the outdoor control unit by the spacers (

3

 ).

(8) Screw the Compressor IPDU to the heat sink by the four

screws that were removed in step (3). If the screws are loose,

the effect component will generate heat, and cause it to

breakdown. Do not use an electric driver or an air driver.

As it can cause component damage. The torque of the

screws for DB01 is “0.55N•m” and it for Q201 is “1.2N•m”.

(9) Re-connect the connectors and fast-on terminals (

1

 ). Be

sure that all the connectors and the fast-on terminals are

connected correctly and securely inserted.

(10) If the components on the PCB were bent during this

procedure, straighten them so they do not touch other

parts.

(11) Install the cover, then turn on the supply. Check the

operation.

DB01

Q201

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов