Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 280

Страница: 280 / 333

– 280 –

Procedure 2: Replacing P.C. Board

Replace the faulty P.C. board with a service P.C. board.

Be sure to replicate the old jumper setting (removal), switch setting (SW501), and connector short-circuit

setting (Ex. CN34) on the service P.C. board. (See the diagram at below.)

(MCC-1403)

(MCC-1402)

CN030

CN41

CN34

CN041

From left: CN112, 111 and 110

If a short-circuiting plug had been used on the
replaced P.C. board, reuse it on the service P.C. board.

If a short-circuiting plug had been used on the replaced
P.C. board, reuse it on the service P.C. board.

A B

Indoor unit

P.C. board

A B

Indoor unit

Group control wiring

P.C. board

Indoor unit

P.C. board

Indoor unit

P.C. board

A B

Indoor unit (one being serviced)

Service P.C. board

Remote controller

Indoor unit (one being serviced)

Service P.C. board

Remote controller

A B

Case 1

Case 2

CN
41

Remove group control wiring from terminals
A and B of indoor unit being serviced, and
connect remote controller wiring.

Remove CN41
connectors of all
other indoor units
in same group.

It is necessary to establish a one-to-one correspondence between the indoor unit being

serviced and the remote controller.

Turn on the indoor unit using one of the methods described below according to the system configuration.

(1) Single (stand-alone) operation

Turn on the indoor unit and proceed to

Procedure 3

(2) Group operation

A) If it is possible to selectively turn on the indoor unit being serviced

Turn on the indoor unit being serviced and proceed to

Procedure 3

B) If it is not possible to selectively turn on the indoor unit being serviced (

Case 1

)

a) Temporarily disconnect the group control wiring from terminals A and B of the indoor unit being serviced.

b) Connect the remote controller wiring to the terminals, turn on the indoor unit, and proceed to

Procedure 3

* If this method cannot be used, proceed to the alternative method described below (

Case 2

C) If it is not possible to selectively turn on the indoor unit being serviced (

Case 2

)

a) Remove the CN41 connectors of all other indoor units in the same group.

b) Turn on the indoor unit and proceed to

Procedure 3

* Be sure to restore the temporarily removed group control wiring and CN41 connectors to their initial states

after Procedure 3 has been completed.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 280 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: