Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 261

– 261 –

<Installing compressor>

• Install a compressor by following the dismantling procedure in reverse.

WARNING

The dismantling process may have loosened compressor leads and faston connectors. Prior to installation,

therefore, tighten them a little with a pair of pliers, and verify that they are tight after reconnection.

Notes:

• Although a compressor is provided with only two hexagonal bolts, it is standard.
• The tightening torque of the hexagonal bolts, used to mount the compressor, is 200kg/cm.
• If oil has been drawn from the accumulator, repair the cut pipe through pinching and brazing.

<Vacuum-pumping>

(Single outdoor unit system)
• Before performing vacuum-pumping, fully open PMV1, 2 and 4. If they are closed, the heat exchangers of the

outdoor unit cannot be vacuum-pumped.

• Connect a vacuum pump consecutively to the check joints placed in the liquid and discharge pipes and on

the high-pressure side of the suction pipe, and turn it on.

• Operate the vacuum drying until the vacuum gauge indicates 1 mmHg.

<Method to fully open PMV manually>

(1) Turn on the power switch of the outdoor unit.
(2) With the Bits 1 and 2 of SW12 set to off, short-circuit the pins of CN30.
(3) Disconnect the connectors of PMV1 and 2 from the I/F P.C. board.
(4) With the Bits 1 and 2 of SW12 set to off and on, respectively, short-circuit the pins of CN30.
(5) Disconnect the connector of PMV4 from the I/F P.C. board
(6) Turn off the power switch of the outdoor unit.

<Refrigerant charging>

• Inject the same amount of refrigerant as the recovered residual refrigerant via the charging port of the liquid-

side service valve.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
259
260
261
262
263
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов