manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 257 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 257

– 257 –

11. REPLACING COMPRESSORS

11-1. Compressor Replacement Procedure (Outline)

NO

YES

YES

NO

START

Is the outdoor unit the only one in the system?

Recover refrigerant 
from the failed unit in 
accordance with “10 
OUTDOOR UNIT 
REFRIGERANT 
RECOVERY
METHOD”.

Manually open PMV1, 2 
and 4 of the failed unit 
(by short-circuiting the 
pins of CN30 on I/F P.C. 
board and turning off the 
power switch), and 
recover refrigerant using 
a refrigerant recovery 
device (*1).

Turn off the power switch of the failed outdoor unit.

Dismantle the faulty compressor.

Check the color of the oil in the faulty compressor.
ASTM grade: Is it 4 or above?
(Judge the condition of the oil against color samples,
and decide whether to replace the replace to the
failed compressor only or all the compressors in the
failed outdoor unit.)

Replace both the faulty compressor and the normal 
compressor(s).

Measure the amount of oil in the normal compressor(s).

Adjust the amount of oil according to the oil quantity 
measurement result(s).

Install the new compressor(s) (*2).

Perform a leakage check of the failed outdoor unit.

Perform vacuum drying in the failed outdoor unit.

Refrigerant charging

END

Measure the amount of oil in the faulty compressor.

Replace the faulty compressor only.

Amount of oil

4300cc

6700cc

MAP0804

∗

, 1004

∗

MAP1204

∗

, 1404

∗

 WARNING

In situations such as indoor unit relocation and

repairs, it is not possible to recover all the

refrigerant held by the system in the outdoor units.

It could cause a serious accident, such as blow out

or injury.

Be sure to perform refrigerant recovery using a

refrigerant recovery device.

 WARNING

When detaching a pipe by heating with a burner a

welded joint, take care as any oil left in the piping

may burn in a momentary flash of fire when the

weld filler metal melts.

*1 The full-opening of PMV1, 2 and 4 via short-

circuiting of the CN30 pins is automatically

undone after 2 minutes, causing the valves to fully

close. To maintain fully open state, turn off the

power switch of the outdoor unit within 2 minutes.

*2 The SHRM-i (4 series) and the SHRM (2 series)

use different types of compressors.

Be sure to check the service part code.

This flowchart only shows the standard compressor

replacement procedure. Since the situation can differ

site by site, perform the task in accordance with the

following judgment criteria:
(1) New compressors are charged with 1900cc of oil

per unit.

(2) The amount of oil held by an outdoor unit is as

shown below.

(3) When a compressor is dismantled, it usually

contains 800-1400cc oil.

The amount of oil held by an oil separator is

usually 0-1000cc for MAP0804

∗

, MAP1004

∗

 and

0-1500cc for MAP1204

∗

 and MAP1404

∗

.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов