Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 221

Страница: 221 / 333

– 221 –

[P17]

Chec

k code

Cause

Chec

k code name

Discharge temper

ature

TD3 error

Outdoor unit ser

vice v

alv

e closed

Outdoor PMV1, 2 error

TD sensor error

Refr

iger

ant shor

tage

, clogging inside of pipe

4-w

y v

alv

e error

SV4 circuit leakage

, misinstallation

SV5 circuit clogging

SV6 circuit clogging

. Incorrect piping of discharge gas/suction gas pipe

10.

Cooling/Heating FS unit error

Are

ser

vice v

alv

es of outdoor

unit discharge gas pipe

, suction

gas pipe

, liquid pipe

fully opened?

Are

outdoor PMV

, 1.

Connector connection

Wir

ing, 3.

Coil, 4.

alv

e body

Outdoor P

. board nor

mal?

resistance char

acter

istics

of TD3

sensor

nor

mal?

asn't

discharge gas b

ypass to

suction side b

4-w

y v

alv

SV5

circuit leakage

chec

SV6

circuit clogging

chec

Chec

incorrect piping of discharge

gas/suction gas

main pipes

Cooling/Heating

FS unit

nor

mal?

Isn't

an indoor unit of diff

erent

refr

iger

ant line

connected?

∗

Connectors:

PMV1:

CN300

PMV2:

CN301

PMV4:

CN303

Open ser

vice v

alv

es fully

Repair outdoor PMV

Replace TD3

sensor

4-w

y v

alv

e chec

Correct instllation of v

alv

e coil.

Replace SV43 v

alv

Replace def

ectiv

e par

Replace def

ectiv

e par

Correct piping as standard.

Repair Cooling/Heating

FS unit

Correct wir

ing as standard.

* See "Outdoor unit temper

ature sensor

char

acter

istics" on "8-

. Sensor Char

acter

istics".

The

y are refr

iger

ant shor

tage

clogging and pipe breakage

(That is

, confir

m there is no pipe breakage

and then recharge refr

iger

ant.)

SV4 circuit

Are SV41, SV42 and SV43

valv

e coils installed correctly?

Is SV42 circuit sealed

correctly (no leakage)?

[P1

]

Sub-code:

Detected outdoor unit No

Chec

k code

Cause

Chec

k code name

4-w

y v

alv

e re

erse error

4-w

y v

alv

e error

TS1 sensor/TE1 sensor error

Pd sensor/Ps sensor error

TE sensor/TL sensor misconnection

SV14 v

alv

e circuit oper

ation error (Coil wir

ing f

alls out)

Is 4-w

y v

alv

coil connector

connected?

Are output v

oltage

char

acter

istics of Pd and

Ps sensors nor

mal?

Are

char

acter

istics of

resistance v

alue of

TS1,

TE1 and

TL sensors

nor

mal?

Are TS1, TE1

and TL

sensor

connectors connected

nor

mally?

Does

discharge refr

iger

ant

gas b

ypass to suction

side through 4-w

valv

e? *1

Does 4-w

y v

alv

oper

ate?

Correct connector connection.

(4-w

y v

alv

e coil:

CN317)

Sensor error

Correct connector connection

TS1 sensor

: CN505

TE1 sensor

: CN520

TL sensor

: CN523

If no error occurs in the test

oper

ation, restar

t oper

ation.

4-w

y v

alv

e error

Chec

k 4-w

y v

alv

Reset the po

er supply and

star

t heating test oper

ation.

*1 Chec

TS1 and

TE1 temper

ature of the outdoor unit which is r

unning.

(I/F) SW01=[1], SW02=[7], SW03=[2]

→

TS sensor temper

ature

SW01=[1], SW02=[

], SW03=[2]

→

TE sensor temper

ature

udgment cr

iter

ia>

TE1 sensor

: Nor

mal if

TE1 is 30

C or less in the seasons e

xcept

summer (Outside temp 20

C or lo

er)

TS1 sensor

: Nor

mal if

TS is 50

C or less in the seasons e

xcept

summer (Outside temp 20

C or lo

er)

* See "Outdoor unit temper

ature sensor

char

acter

istics" on "8-

. Sensor Char

acter

istics".

Cooling/Heating

FS unit nor

mal?

Repair Cooling/Heating FS unit.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 221 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: