Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 22

Страница: 22 / 333

– 22 –

4. Tools

(1) Required Tools for R410A

Mixing of different types of oil may cause a trouble such as generation of sludge, clogging of capillary, etc.

Accordingly, the tools to be used are classified into the following three types.

1) Tools exclusive for R410A (Those which cannot be used for conventional refrigerant (R22))

2) Tools exclusive for R410A, but can be also used for conventional refrigerant (R22)

3) Tools commonly used for R410A and for conventional refrigerant (R22)

The table below shows the tools exclusive for R410A and their interchangeability.

Tools exclusive for R410A (The following tools for R410A are required.)

General tools (Conventional tools can be used.)

Explanation of symbols

: Newly prepared (It is necessary to use it exclusively with R410A, separately from those for R22 or R407C.)

: Former tool is available.

Gauge manifold

Vacuuming, charging refrigerant
and operation check

Exclusive to R410A

Used tools

Usage

Proper use of tools/parts

Charging hose

Exclusive to R410A

Gas leak detector

Checking gas leak

Exclusive to R410A

Vacuum pump

Vacuum drying

Usable if a counter-flow preventive adapter is attached

Vacuum pump with counterflow

Vacuum drying

R22 (Existing article)

Flare tool

Flare processing of pipes

Usable by adjusting size

Bender

Bending processing of pipes

R22 (Existing article)

Refrigerant recovery device

Recovering refrigerant

Exclusive to R410A

Torque wrench

Tightening flare nut

Exclusive to Ø12.7mm and Ø15.9mm, Ø19.1mm

Pipe cutter

Cutting pipes

R22 (Existing article)

Refrigerant canister

Charging refrigerant

Exclusive to R410A
Enter the refrigerate name for identification

Welding of pipes

R22 (Existing article)

Welding machine/Nitrogen gas
cylinder

Charging cylinder

Charging refrigerant

Unusable (Use the Refrigerant charging balance.)

Charging cylinder

Charging refrigerant

Unusable (Use the Refrigerant charging balance.)

(Note 1)

When flaring is carried out for R410A using the conventional flare tools, adjustment of projection margin is

necessary. For this adjustment, a copper pipe gauge, etc. are necessary.

(Note 2)

Charging cylinder for R410A is being currently developed.

In addition to the above exclusive tools, the following equipments which serve also for R22 are necessary as
the general tools.
(1) Vacuum pump

(7) Screwdriver (+, –)

Use vacuum pump by attaching vacuum pump

(8) Spanner or Monkey wrench

adapter.

(9) Hole core drill

(2) Torque wrench

(10)Hexagon wrench (Opposite side 4mm)

(3) Pipe cutter

(11)Tape measure

(4) Reamer

(12)Metal saw

(5) Pipe bender
(6) Level vial

Also prepare the following equipments for other installation method and run check.
(1) Clamp meter

(3) Insulation resistance tester

(2) Thermometer

(4) Electroscope

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 22 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: