Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 190

– 190 –

Check code

Location

of

detection

System status

Description

Error detection

condition(s)

Check items (locations)

Outdoor 7-segment display

Main

remote

controller

Check

code

Sub-code

I/F

01: TS condition

P15

P15

P17

—

P17

All stop

Protective shutdown due to
sustained suction
temperature at or above
judgment criterion
for at least 10 minutes is
repeated four times or more.
<TS error judgment criterion>
In cooling operation: 60˚C
In heating operation: 40˚C

• Check for insufficiency in
refrigerant quantity.
• Check outdoor service valves
(discharge gas side, suction
gas side, liquid side) to
confirm full opening.
• Check PMVs (PMV1, 2, 4) for
clogging.
• Check resistance
characteristics of TS1 sensor.
• Check for defect in 4-way
valve.
• Check SV4 circuit for leakage
• Check SV5 circuit leakage.
• Check mispiping of discharge
gas/suction gas main pipes.
• Check Cool/Heat FS unit.
Check SVD valve, SVS valve
leakage.
(Check SVDD valve, SVSS
valve leakage.)
Connecting piping to FS unit
Mispiping of (discharge gas/
suction gas)

Gas
leakdetection
(TS1 condition)

I/F

All stop

Discharge temperature (TD2)
exceeds 115˚C.

• Check outdoor service valves
(discharge gas side, suction
gas side, liquid side) to
confirm full opening.
• Check outdoor PMVs
(PMV1, 2, 4) for clogging.
• Check resistance
characteristics of TD2 sensor.
• Check for defect in 4-way
valve.
• Check SV4 circuit for leakage.
• Check SV4 circuit (for wiring
or installation error involving
SV41, SV42 and SV43).
• Check SV5 valve circuit
leakage.
• Check SV6 circuit (Clogging,
valve operation error)
• Check mispiping of discharge
gas/suction gas main pipes.
• Check Cool/Heat FS unit.
Check SVD valve, SVS valve
leakage.
(Check SVDD valve, SVSS
valve leakage.)
Connecting piping to FS unit
Mispiping of (discharge gas/
suction gas)
Check wiring between FS unit
and indoor unit, connection of
connectors
Check miswiring of SVS/SVD
valve.

Discharge
temperature TD2
error

I/F

02: TD condition

All stop

Protective shutdown due to
sustained discharge
temperature (TD1, TD2 or TD3)
at or above 108˚C for at least
10 minutes is repeated four
times or more.

• Check for insufficiency in
refrigerant quantity.
• Check PMVs (PMV 1, 2, 4) for
clogging.
• Check resistance
characteristics of TD1, TD2
and TD3 sensors.
• Check indoor filter for
clogging.
• Check piping for clogging.
• Check SV4 circuit (for leakage
or coil installation error).
• Check mispiping of discharge
gas/suction gas main pipes.
• Check Cool/Heat FS unit.
Check SVD valve, SVS valve
leakage.
(Check SVDD valve, SVSS
valve leakage.)
Connecting piping to FS unit
Mispiping of (discharge gas/
suction gas)
Check wiring and connection
of connectors between FS
unit and indoor unit.
Check miswiring of SVS/SVD
valves.

Gas leak
detection
(TD condition)

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
188
189
190
191
192
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов