Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 160

Страница: 160 / 333

– 160 –

7-7-3. Remote Controller Distinction Function

This function is provided to distinguish the remote controller connected to the indoor unit from the outdoor unit

for a refrigerant circuit system by using switches on the interface P.C. board of the header unit.
<Distinction procedure>

Power ON

End

Check the connected remote controller

Operation

7-segment display

[A] [B]

[ A 1 ] [

]

7-segment display

[A] [B]

[ A 1 ] [ FF]

Be sure to turn on the power of the indoor unit
prior to the power of the outdoor unit.

Set the display select switches on the
interface P.C. board of the header unit
as follows:
Set SW01/SW02/SW03 to [2/4/1]

Push the push switch SW04 on the
same board for 2 seconds or more.

"Checking" display of the connected
remote controller flashes.

Push the push switch SW05 on the
interface P.C. board of the header
unit for 2 seconds or more.

Other end conditions:
1. 10 minutes has passed
2. SW01, SW02, or SW03 changed to other position.

Interface P.C. board

SW04

SW05

SW02

SW03

SW01

7-segment display [A]

7-segment display [B]

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 160 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: