manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 150 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 150

– 150 –

(2) Test operation

Note 1

Note 2

Note 3

START

Normal

Notes 1-3 are on the next page.

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

Test operation for one indoor unit

Operation starts

Is cold air or hot air discharged?

Is air circulation sufficient?

Operate all the indoor units at once.

Is there adequate temperature difference 

between suction and discharge?

Is the operating voltage correct? 

(220-240 V ±10%)

Is the operating current normal?

Is the operating pressure normal?

Refer to "Test operation procedure" 
of the indoor remote controller.

Check the operating status of the 
compressor.

Execute a test operation using 
"Start/Stop Function of the Indoor 
Unit from Outdoor Unit" in the 
"Service Support Function" section.

• Check power voltage of 

the main power supply.

• Check the cable size of 

the power supply.

• Check the temperature load of the 

indoor/outdoor units.

• Check the pipe length and refrigerant 

amount.

• Check the operating Hz of the 

compressor.

• Check the operation of the outdoor 

fans.

• Check for abnormal sound in the 

outdoor unit.
(Abnormal sound, etc. of the 
compressor and other components)

Check the direction of the louver.

The operation does not start for 
approximately 3 minutes after 
powering-on or stopping operation.

Note: After powering-on, it may 

require up to 10 minutes to start 
the operation due to the initial 
communications of the system.

T

est operation for every indoor unit in turn

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов