Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 148

– 148 –

7-6-2. Single cooling/Single heating Test Operation Check

The Single cooling/Single heating test operation check can be performed on both the indoor remote controller

and the outdoor header unit interface PC board.
(1) Test operation start/stop operation
Test operation from the indoor remote controller
• Wired remote controller: Refer to the items below in “Test operation” of the wired remote controller.
• Wireless remote controller: Refer to the items below in “Test operation” of the wireless remote controller.
• Lite-Vision plus remote controller : Refer to the installation manual of RBC-AMS51E

Wired remote controller

Wireless remote controller (Except the 4-

way Cassette type and the Ceiling type)

Test run (Forced cooling operation)

Requirement:

• Finish the forced cooling operation in a short

time because it applies excessive strength to the

air conditioner.

How to perform forced cooling operation

1.

When TEMPORARY button is pushed for 10

seconds or more, “Pi!” sound is heard and the

operation changes to a forced cooling operation.

After approx. 3 minutes, a cooling operation starts

forcedly.

Check cool air starts blowing. If the operation does

not start, check wiring again.

2.

To stop a test operation, push TEMPORARY

button once again (Approx. 1 second).
• Check wiring / piping of the indoor and outdoor

units in forced cooling operation.

1, 5

3

2, 4

Operation content

Procedure

1

2

When the Test button is pushed for 4 seconds or
more, “TEST” is displayed in the display section,
and the unit enters test operating mode.

5

Push the Test button to clear the test operating mode.
(“TEST” disappears from the display section, and
the status returns to the normal stopped status.)

3

Using the Select Mode button, select the
“ COOL” or “ HEAT” operating mode.
• Do not use an operating mode other than
“ COOL” or “ HEAT”.
• Temperature adjustment is unavailable during
test operation.
• Error is detected as usual.

Push the button.

4

When the test operation has finished, push the
button to stop the operation.
(The same display as in procedure 1 appears in
the display section.)

TEMPORARY-Taste

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
146
147
148
149
150
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов