manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 143 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 143

– 143 –

7-5.

TROUBLESHOOTING IN TEST OPERATION

If there are phenomena such as the output of a check code or the remote controller is not accepted when

poweredon after wiring work or during address setup operation, the following causes are considered.

7-5-1. A Check Code Is Displayed on the Remote Controller

Check the code 

displayed on the 

indoor remote 

controller

Header

unit 7-

segment 

display

Cause

Countermeasures

E04

–

When outdoor power is off

Check that the header outdoor unit power is on

L08

Address setup error
• Only line addresses of the connected indoor units 

are undefined.

• The outdoor line address and the line addresses 

of all the indoor units do not match.

• The indoor addresses are duplicated. (Units 

except those displaying E04 are duplicated.)

• A header unit is not set up in group control (except 

groups displaying E04).

Set up the address again.

E08 

⇔ 

-XX

Alternate 

blinking

Duplication of indoor addresses (address number in 
the subcode of the check code are duplicated).

Set up the address again.

E07

There is no outdoor terminal resistance, or 
there are two or more resistances.
(After address setup, when terminal 
resistance setup is changed after powering-
on)

Check SW30 bit 2 of the header unit.
No connection between multiple refrigerant lines: 
SW30 bit 2 is on.
Connection between multiple refrigerant lines: 
SW30 bit 2 of the connected header unit is turned on 
only for one line.

Transmission circuit error at the interface side (PC 
board failure)

Replace the interface PC board.

E06

After address setup, communication from all the 
indoor units is interrupted under the condition that a 
normal operation can be performed.

Check and correct disconnection of the indoor/
outdoor communication line (the communication line 
between the header unit and the leading indoor 
unit).
Check for the influence of communication noise.

E16

E16 

⇔ 

-XX

Alternate 

blinking

Exceeded the number or capacity of connected 
indoor units

Adjust the number or capacity of connected indoor 
units.

E23

E23

Communication between outdoor units has stopped. Check the number of connected outdoor units.

Check that outdoor unit power is on.

E25

E25

Duplication of outdoor addresses (only when an 
outdoor address was manually set up)

Do not use manual setup for outdoor addresses.

E26

E26 

⇔ 

-XX

Alternate 

blinking

Number of connected outdoor units has decreased.
• When installing an outdoor backup
• The power of a follower unit is not turned on.

Correction of the cause of error occurrence
• If it occurs when installing a backup, clear the error 

after setup finishes.

• If the power of a follower unit is not turned on, turn 

on the power.

L04

L04

Duplication of outdoor line addresses
• Line address setup error (occurred after 

connection between U1/U2 and U3/U4 
connectors)

Modify the line address setup of the header unit 
between lines. (Set up SW13 and SW14 on the 
interface PC board.)

L05(*)

L06

Duplication of indoor units with priority

Set up priority only for one indoor unit.

L06(*)

There are two or more indoor units set up with 
priority.

Among indoor units indicating “L05,” set one unit 
with priority.

L08

L08

Address setup error
• Only indoor addresses of all the connected indoor 

units are undefined.

Set up the addresses again.
Modify the setup.

ON

1

2

SW30

* “L05”: Displayed on the indoor unit set up with priority

“L06”: Displayed on the indoor units except the one set up with priority

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов