manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 141 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 141

– 141 –

7-4-5. Setting when connecting multiple indoor units to a FS (Flow Selector) unit

 

 

 

 

NG

NG

Control wiring
between indoor
unit and FS unit
(Within 15 m)

Piping

Piping

Piping

FS unit

FS unit

FS unit

Control wiring
between
indoor unit
and FS unit

Remote controller

Remote controller

Indoor
unit

Indoor
unit

Group control

Group control

FS unit

Piping

Control wiring
between
indoor unit
and FS unit

Remote controller

Indoor
unit

Cautions to connection of indoor unit

• When connecting the multiple indoor units to a

single FS unit, it is necessary to set up the CODE

No..

Be sure to set up the CODE No. after setup of

address.

• When connecting the multiple indoor units to a

single FS unit, only group control is available.

For the indoor unit, a remote controller cannot be

individually connected.

• FS unit must be connected to one of the multiple

indoor units which is under group control of a

remote controller. The distance between FS unit

and the indoor unit must be within 15 m.

Incorrect example of connection

How to set up CODE No.

5

4

2

3

1

.

1

Push 

 + 

TEST

 buttons simultaneously for

4 seconds or more.

•

ALL

 is displayed in the UNIT No. window.

• In this time, the fans of all the indoor units in

the group control start the fan operation.

2

Using the set temperature buttons 

 /

 , select the CODE No. “

0E

”.

3

Change SET DATA to “

01

” by the timer

buttons 

 / 

 .

4

Push 

SET

 button.

5

Push 

TEST

 button. Then the setup finished.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов