Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 125

– 125 –

7-3. Check at Main Power-on

After turning on the main power of the indoor units and outdoor unit in the refrigerant line to conduct a test

operation, check the following items in each outdoor and indoor unit.

(After turning on the main power, be sure to check in order: indoor unit

→

outdoor unit.)

<Check on the outdoor unit>

(1) Check that all the rotary switches, SW01, SW02, and SW03, on the interface PC board of the header unit

are set to “1.”

(2) If another check code is displayed on the 7-segment display [B], remove the cause of the problem referring

to Section, “8 TROUBLESHOOTING”.

(3) Check that “L08” is displayed on the 7-segment display [B] on the interface PC board of the header unit.

(L08: Indoor address not set up)

(If the address setup operation has already been completed during servicing, etc., the above check code is

not displayed, and “U1” is displayed on the 7-segment display [A].)

Interface PC board

SW01

SW02

SW03

SW04

D600 D601 D602 D603 D604

SW15

SW05

Push switches

Rotary switches

7-segment display

[A]

7-segment display

[B]

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

CL

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT LOUVER

Normal status
(power supplied and operation stopped)

Good

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

CL

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT LOUVER

When power is not supplied normally

No good

<Check on the indoor unit>

(1) Display check on the remote controller (in the case of a wired remote controller)

Check that a frame, as shown in the following figure at left, is displayed on the LC display section of the

remote controller.

If no frame is displayed, as shown in the above figure at right, the remote controller does not have a normal

supply of power; check the following items.
• Check the power supply of the indoor unit.
• Check the cabling between the indoor unit and the remote controller.
• Check whether there is a cutoff of wire around the indoor control PC board or not, and check for

connection failures of the connectors.

• Check for failure of the transformer for the indoor electrical control box.
• Check for failure of the indoor control PC board.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
123
124
125
126
127
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов