Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 115

– 115 –

6-8-6. Operation Mode Selection Control : TCB-PCMO4E

SW1: Cooling mode specified input switch
SW2: Heating mode specified input switch

CN510

PJ17

TB1

SW1

SW2

COM

HEAT

COOL

Locally procured

Optional PCB

Header outdoor unit

Shield
wire

Connection
cable

Outdoor unit

interface PCB

Input signal

Operation

Remarks

COOL (SW1)

HEAT (SW2)

ON

OFF

Only cooling

operation allowed

*

OFF

ON

Only heating

operation allowed

*

OFF

OFF

Normal operation

Jumper wire

Description of intervention

J01 connected

(factory default)

All indoor units operating in a mode different from the selected operation mode (prohibited-mode indoor units)
become non-priority units (thermostat OFF).
Prohibited-mode indoor units

J01 cut

The selected operation mode is imposed on all indoor units operating in a different mode.

Operation mode

Operation status

Remote controller

display

COOL

Fan operation at air flow rate set via remote controller

“

” operation ready

HEAT

Fan operation at extremely low air flow rate

FAN

Fan operation at air flow rate set via remote controller as
normal

Mode selected at P.C. board

Remote controller operation / display

Normal

All modes (COOL, DRY, HEAT and
FAN) available

COOL

Only COOL, DRY and FAN available “

operation mode control”

(turned on during remote
controller operation)

HEAT

Only HEAT and FAN available

NOTE

SW1: COOL mode selection switch

SW2: HEAT mode selection switch

* The display “

(Operation mode selection control in progress)” appears on the remote controller

Indoor unit operation intervention function [only supported by SHRM-i and SMMS-i (4 series)]

The statuses of indoor units operating in a mode different from the selected operation mode can be changed

by changing the status of a jumper wire (J01) provided on the interface P.C. board of the header outdoor unit.

The optional P.C. board should be connected to the header outdoor unit (U1).

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
113
114
115
116
117
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов