manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 113 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 113

– 113 –

6-8-3. Snowfall Fan Control : TCB-PCMO4E

SW1: Snowfall detection switch (snowfall sensor)

CN509

PJ17

TB1

SW1

COM

HEAT

COOL

Locally procured

Optional PCB

Snowfall sensor

Header outdoor unit

Connection
cable

Outdoor unit 

interface PCB

Shield
wire

Terminal

Input signal

Operation

COOL
(SW1)

Snowfall fan control
(Turns on outdoor 
unit fan)

Normal operation
(Cancels control)

ON

OFF

ON

OFF

SW1: Operation input switch
SW2: Stop input switch

CN512

PJ17

TB1

SW1

SW2

COM

HEAT

COOL

Locally procured

Optional PCB

Header outdoor unit

Outdoor unit 

interface PCB

Connection
cable

Shield
wire

Terminal

Input signal

Operation

COOL
(SW1)

Turns on all indoor 
units

HEAT

(SW2)

Turns off all indoor 
units

ON

OFF

ON

OFF

Operation

An external snowfall signal turns on the outdoor unit fan.

The input signal is recognized during its rising/falling phase.

(After reaching the top/bottom of the rising/falling edge, the signal must remain there for at least 100 ms.)

The optional P.C. board should be connected to the header outdoor unit (U1).

6-8-4. External master ON/OFF Control : TCB-PCMO4E

Operation

The system is started/stopped from the outdoor unit.

The input signal is recognized during its falling phase. (After reaching the bottom of the falling edge, the signal

must remain there for at least 100 ms.)

CAUTION

(1) Do not turn on the COOL (SW1) and HEAT (SW2) terminals simultaneously.
(2) Be sure to provide a contact for each terminal.

External signal: No-voltage pulse contact

The optional P.C. board should be connected to the header outdoor unit (U1).

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов