Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 104

Страница: 104 / 333

– 104 –

Codes (DN codes) for changing settings (Necessary for local advanced control)

Item

Description

At shipment

Ventilation fan speed during
nighttime heat purge
operation

0000: Always LOW

0001: Operate at ventilation fan
speed set last time the
operation was stopped

Humidifier type setting

Depends on the type

0000: No humidifier

0001: Humidifier

Power saving mode

0001: Valid

0000: Invalid

0001: Valid

Current ventilation mode

0002: Heat exchange
mode

0002: Heat exchange mode

0003: Automatic mode

Unbalanced fan speed
ventilation

0000: Invalid

0000: Invalid
0002: SA < EA

0001: SA > EA

Linkage with external
devices

0000: ON / OFF linked

0000: ON / OFF linked
0002: OFF linked

0001: ON linked

Damper output

0000: Normal

0001: Nighttime heat purge
compatible

Timer setting
(Wired remote controller)

0000: Possible

0001: Not possible

Current ventilation fan
speed

0002: High

0002: High
0004: Unbalanced

0003: Low

Abnormal signal / Bypass
mode signal switch

0000: Abnormal signal
output

0000: Abnormal signal output

0001: Bypass signal output

Humidity judgment by
outdoor temperature

0000: Not judged

BD Continuous humidifying time

0006: 6 hours

0001: 1 hour

0020: 20 hours

Delay after drainage

0015: 15 minutes

0030: 30 minutes

0000: Not judged

0001: Judged

Nighttime heat purge
setting

0000: Invalid

0000: Invalid
0001: Start in 1 hour

0048: Start in 48 hours

Air to Air intake temperature
correction (Cool)

0004: –2.0˚C

0000: No shift
0002: –1.0˚C

0001: –0.5˚C
0007: –3.5˚C

Air to Air intake temperature
correction (Heat)

0005: 2.5˚C

0000: No shift
0002: 1.0˚C

0001: 0.5˚C
0007: 3.5˚C

Operation output

0000: Normal operation
only

0000: Normal operation only
0002: Nighttime heat purge only
0004: Exhausting fan linked

0001: Nighttime heat purge
0003: Supplying fan linked

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 104 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: