Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 333

Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 103

– 103 –

5d

High-ceiling adjustment
(Air flow selection)

0000: Standard

1-way cassette (SH)

Built-in filter

2-way cassette
0000: Standard filter (factory default)
0001: Super long-life filter
4-way cassette
0000: Standard filter (factory default)
Ceiling
0000: Standard filter (factory default)
Concealed duct standard
0000: Standard filter (factory default)
0001: High-performance filter (65%, 90%)

Static pressure selection

Concealed duct standard
0000: Standard (factory default)
0001: High static pressure 1
0003: High static pressure 2
0006: Low static pressure

Slim Duct (AP007~AP018)
0000: Standard (factory default)
0001: High static pressure 1
0003: High static pressure 2
0006: High static pressure 3

Value

Type

AP015, AP018

AP024

0000

Standard (factory default)

3.5 m or less

3.8 m or less

0001

High-ceiling (1)

4.0 m or less

4.0 m or less

0003

High-ceiling (3)

4.2 m or less

4.2 m or less

60

Timer setting
(wired remote controller)

0000: Available

0000: Available (can be performed)

0001: Unavailable (cannot be performed)

DN

Item

Description

At shipment

2-way cassette

* The high-ceiling installation of model AP007 to AP012 can only be

undertaken when the combined capacity of the indoor units connected is
100% or less than the capacity of the outdoor unit.
Do not proceed with high-ceiling installation if this limit is exceeded.

Value

Type

AP007~AP030

AP036~AP056

0000

Standard (factory default)

2.7 m or less

2.7 m or less

0001

High-ceiling (1)

3.2 m or less (*)

3.0 m or less

0003

High-ceiling (3)

3.8 m or less (*)

3.5 m or less

4-way cassette

Value

Type

AP009~AP012

AP015~AP018

Air flow at outlet

4 directions 3 directions 2 directions 4 directions 3 directions 2 directions

0001

High-ceiling (1)

—

—

—

3.2 m

3.5 m

3.8 m

0000

Standard

(factory default)

2.7 m

2.8 m

3.0 m

2.8 m

3.2 m

3.5 m

0003

High-ceiling (3)

—

—

—

3.5 m

3.8 m

—

Value

Type

AP024~AP030

AP036~AP056

Air flow at outlet

4 directions 3 directions 2 directions 4 directions 3 directions 2 directions

0001

High-ceiling (1)

3.3 m

3.5 m

3.8 m

3.3 m

3.5 m

3.8 m

0000

Standard

(factory default)

3.0 m

3.3 m

3.6 m

3.0 m

3.3 m

3.6 m

0003

High-ceiling (3)

3.6 m

3.8 m

—

3.6 m

3.8 m

—

Ceiling

Value

Type

AP015~AP056

0000

Standard (factory default)

3.5 m or less

0001

High-ceiling (1)

4.0 m or less

AMP Air Conditioning

www.ampair.co.uk | [email protected]

«
...
101
102
103
104
105
...
»

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов