manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 101 / 333

Поделиться
Скачать
Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 101

– 101 –

6-5. Method to Set Indoor Unit Function DN Code

When performing this task, be sure to use RBC-AMS51E

∗

 or RBC-AMT32E.

For operation of RBC-AMS51E

∗

, refer to the attached manual.

<Procedure> To be performed only when system at rest

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

CL

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT  LOUVER

5

4

1

2

6

3

(RBC-AMT32E)

1

Push the 

TEST

 + 

SET

 + 

CL

 buttons simultaneously and hold for at

least 4 seconds.

The unit No. displayed first is the address of the header indoor unit in

group control.

Then the fan and louver of the selected indoor unit move.

2

Each time the “Select unit” side of the 

UNIT  LOUVER

 button is

pushed, one of the indoor unit Nos. under group control is

displayed in turn. Then the fan and louver of the selected

indoor unit move.

3

Use the 

TEMP

 button to select the CODE No. (DN code) of

the desired function.

4

Use the 

TIME

 button to select the desired SET DATA

associated with the selected function.

5

Push the 

SET

 button. (The display changes from flashing to

steady.)

• To change the selected indoor unit, go back to step 

2

.

• To change the selected function, go back to step 

3

.

6

When the 

SET

 button is pushed, the system returns to normal

off state.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Отзывы:

Нет отзывов