Toshiba MMY-MAP0804FT7(Z) Скачать руководство пользователя страница 1

Страница: 1 / 333

FILE NO. A12-006

SERVICE MANUAL

AIR-CONDITIONER

MULTI TYPE

PRINTED IN JAPAN, Nov., 2012 ToMo

This service manual provides relevant explanations about new outdoor unit (SHRM-i).

Please refer to the following service manuals for each indoor units.

< SUPER HEAT RECOVERY MULTI -i >

Outdoor Unit
Model name:

MMY-MAP0804FT8(Z)(ZG)-E

MMY-MAP0804FT8(Z)(ZG)-TR

MMY-MAP1004FT8(Z)(ZG)-E

MMY-MAP1004FT8(Z)(ZG)-TR

MMY-MAP1204FT8(Z)(ZG)-E

MMY-MAP1204FT8(Z)(ZG)-TR

MMY-MAP1404FT8(Z)(ZG)-E

MMY-MAP1404FT8(Z)(ZG)-TR

MMY-MAP0804FT8(Z)(ZG)

MMY-MAP0804FT7(Z)(ZG)

MMY-MAP1004FT8(Z)(ZG)

MMY-MAP1004FT7(Z)(ZG)

MMY-MAP1204FT8(Z)(ZG)

MMY-MAP1204FT7(Z)(ZG)

MMY-MAP1404FT8(Z)(ZG)

MMY-MAP1404FT7(Z)(ZG)

A08-004
A10-007
A12-005
A12-005

A10-022-2

SVM-05052-1

SVM-09-059

SVM-11-036

A10-033

<4-way Cassette Type > ( MMU-AP

∗∗∗∗

H )

<2-way Cassette Type > ( MMU-AP

∗∗∗∗

WH )

<Concealed Duct Standard Type> ( MMD-AP

∗∗∗∗

6BH-E )

<Slim Duct Type> ( MMD-AP2244SPH-E, AP274SPH-E )
<Air to Air Heat Exchanger with DX Coil Unit Type>
High-wall Compact Type ( MMK-AP

∗∗∗

4MH-E )(Made in Thailand model)

High-wall Type ( MMK-AP

∗∗∗

3H )(Made in Thailand model)

Console Type ( MML-AP

∗∗∗∗

NH-E )(Made in Thailand model)

Other indoor units ( MM

∗

-AP

∗∗∗∗

H-E )

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Содержание MMY-MAP0804FT7(Z)














































































































































































































































































































































Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы:

Toshiba MMY-MAP0804FT7(Z), Руководство по обслуживанию, Страница: 1 / 333

Результаты поиска

Содержание MMY-MAP0804FT7(Z)

Отзывы: