EN
– 8 –
5
Timer operation
• Three timer modes are available: (Setting of up to 168 hours is enabled.)
Timer operation
Set
1
Push
button.
The Timer mode changes each time the button is
pushed.
•
and timer display flashes.
2
Push
to select “set time”.
• With every push of
button, the set time
increases by 0.5 hr (30 minutes).
When setting a time more than 24 hours for
timer operation, timer can be set in increments
of 1 hr.
The maximum set time is 168 hr (7 days).
The remote control displays the set time with
time (between 0.5 and 23.5 hours) (*
1
) or
number of days and time (24 hours or more) (*
2
)
as shown below.
• With every push of
button, the set time
decreases by 0.5 hr (30 minutes) (0.5 -
23.5 hours) or 1 hr (24 - 168 hours).
Example of remote control display
• In the case of 23.5 hours (*
1
)
• In the case of 34 hours (*
2
)
3
Push
button.
•
display disappears and timer time
display goes on, and
or
display
flashes.
(When ON timer is activated, timer time, ON
timer
are displayed and other displays
disappear.)
4
Cancel of timer operation
Push
button.
Timer display disappears.
NOTE
• When the operation stops after the timer reached
the preset time, the Repeat OFF timer resumes the
operation by pushing
button and stops the
operation after the time of the timer has reached the
set time.
• When
is pushed while the OFF timer function
of the air conditioner is active, the indication of the
timer function disappears and then appears again
after about 5 seconds
.
This is due to normal processing of the remote
control.
OFF timer
: The unit stops when the set time is reached.
Repeat OFF timer : The unit stops daily when the set time is reached.
ON timer
: The unit starts when the set time is reached.
1
3
2
4
(OFF timer)
(ON timer)
(Repeat OFF timer)
No display
OFF
OFF
ON
shows 1 day (24 hours).
shows 10 hours. (Total 34 hours)
Number of days Time
SWING/FIX
6
Installation
Location
• Avoid installing near machines emitting high frequency waves.
• Not suitable for chemical plants such as liquefied carbon dioxide refrigerant plants.
• Places where iron or other metal dust is present. If iron or other metal dust adheres to or collects on the interior
of the air conditioner, it may spontaneously combust and start a fire.
• A failure may occur in certain locations such as the following:
• Areas with large amount of oil droplets (including machine oil) or vapors
• Salty areas near oceans, etc.
• Hot springs emitting sulfidizing gas.
• Heavily acidic or alkaline places.
Special maintenance or parts are required for use in the above places. For details, contact the dealer where you
purchased the product.
• Leave an enough space around the air intake and outlet of the outdoor unit so that the ventilation is not restricted.
• Avoid places where strong wind may blow against the air intake and discharge of the outdoor unit.
• Attach a snow stand, snow hood, etc. to the outdoor unit for use in snowfall areas. For details, contact the dealer
where you purchased the product.
• Make drain water from the outdoor unit is emitted into places with good drainage.
• Attach the air filter to the indoor unit. If not, dust may accumulate on the heat exchanger or other parts in the air
conditioner and cause a water leak.
• Keep a distance of at least 3.3 ft (1 m) between the air conditioner / remote control and a TV or radio. Failure to
observe this precaution may cause visual disturbance or noise.
• Leave a distance of at least 4.9 ft (1.5 m) between the air discharge and a fire alarm. If this precaution is not
observed, the alarm may not work properly or detect fire in case of fire.
Be careful of operation sounds
• Locate the unit in a place secure enough so that the sounds and vibrations do not increase.
• If something is placed near the air discharge of the outdoor unit, noise may increase.
• Do not disturb neighbors with cool / warm air or noise coming from the air discharge of the outdoor unit.
15-EN
16-EN
+00EH99943901_00Ta.book Page 8 Thursday, May 23, 2013 7:17 PM