background image

– 3 –

SMMS 1-Way Cassette YH Type

Installation Manual

SMMS 1-Way Cassette YH Type

Installation Manual

1

Precautions for Safety

The manufacturer shall not assume any liability for the damage caused 
by not observing the description of this manual.

General

• Before starting to install the air conditioner, read carefully through the 

Installation Manual, and follow its instructions to install the air 

conditioner.

• Only a qualified installer(*1) or qualified service person(*1) is allowed 

to install the air conditioner. If the air conditioner is installed by an 

unqualified individual, a fire, electric shocks, injury, water leakage, 

noise and/or vibration may result.

• Do not use any refrigerant different from the one specified for 

complement or replacement. Otherwise, abnormally high pressure 

may be generated in the refrigeration cycle, which may result in a 

failure or explosion of the product or an injury to your body.

• Before opening the intake grille of the indoor unit or service panel of 

the outdoor unit, set the circuit breaker to the OFF position. Failure to 

set the circuit breaker to the OFF position may result in electric 

shocks through contact with the interior parts. Only a qualified 

installer(*1) or qualified service person(*1) is allowed to remove the 

intake grille of the indoor unit or service panel of the outdoor unit and 

do the work required.

• Before carrying out the installation, maintenance, repair or removal 

work, be sure to set the circuit breaker to the OFF position. 

Otherwise, electric shocks may result.

• Place a “Work in progress” sign near the circuit breaker while the 

installation, maintenance, repair or removal work is being carried out. 

There is a danger of electric shocks if the circuit breaker is set to ON 

by mistake.

• Only a qualified installer(*1) or qualified service person(*1) is allowed 

to undertake work at heights using a stand of 50 cm or more or to 

remove the intake grille of the indoor unit to undertake work.

• Wear protective gloves and safety work clothing during installation, 

servicing and removal.

• Do not touch the aluminium fin of the unit. You may injure yourself if 

you do so. If the fin must be touched for some reason, first put on 

protective gloves and safety work clothing, and then proceed.

WARNING

• Do not climb onto or place objects on top of the outdoor unit. You may 

fall or the objects may fall off of the outdoor unit and result in injury.

• When working at heights, use a ladder which complies with the ISO 

14122 standard, and follow the procedure in the ladder’s instructions. 

Also wear a helmet for use in industry as protective gear to undertake 

the work.

• When cleaning the filter or other parts, set the circuit breaker to OFF 

without fail, and place a “Work in progress” sign near the circuit 

breaker before proceeding with the work.

• When working at heights, put a sign in place so that no-one will 

approach the work location, before proceeding with the work. Parts 

and other objects may fall from above, possibly injuring a person 

below. Furthermore, while carrying out the work, wear a helmet for 

protection from falling objects.

• The refrigerant used by this air conditioner is the R410A.

• You shall ensure that the air conditioner is transported in stable 

condition. In case an accident such as dropping of the unit occurs 

while transporting the air conditioner, contact the dealer.

• When the air conditioner must be transported by hand, carry it by two 

or more people.

• Do not move or repair any unit by yourself. There is high voltage 

inside the unit. You may get electric shock when removing the cover 

and main unit.

• This appliance is intended to be used by expert or trained users in 

shops, in light industry, or for commercial use by lay persons.

Selection of installation location

• If you install the unit in a small room, take appropriate measures to 

prevent the refrigerant from exceeding the limit concentration even if 

it leaks. Consult the dealer from whom you purchased the air 

conditioner when you implement the measures. Accumulation of 

highly concentrated refrigerant may cause an oxygen deficiency 

accident.

• Do not install the air conditioner in a location that may be subject to a 

risk of exposure to a combustible gas. If a combustible gas leaks and 

becomes concentrated around the unit, a fire may occur.

• When transporting the air conditioner, wear shoes with additional 

protective toe caps.

• When transporting the air conditioner, do not take hold of the bands 

around the packing carton. You may injure yourself if the bands 

should break.

5-EN

6-EN

Содержание MMU-AP0074YH1-E





























Отзывы: