background image

– 71 –

Codes (DN codes) for changing settings

Codes in the table below are necessary for local advanced control.

* Adjusting this setting is necessary for the header unit when using a system equipped with the Air to Air Heat Exchanger 

with DX Coil Unit only, and the Air to Air Heat Exchanger with DX Coil Unit with the smallest indoor unit address number 

when using a system equipped with the Air to Air Heat Exchanger with DX Coil Unit and air conditioners.

Code

Description

SET DATA and description

Factory default

Note

01

Lighting-up hours of 

the Filter Sign

0000: None
0001: 150 H
0002: 2500 H
0003: 5000 H
0004: 10000 H

0002: 2500 H

Adjusting this setting is 

necessary for the header unit.

06

Detect temperature 

shift value when 

heating

0000: No shift
0001 – 0006: 
[SET DATA value] × 1 °C shift

0002: 2 °C shift

31

Single operation of 

the fan

0000: Invalid
0001: Valid
ON/OFF operation for the Air to Air 

Heat Exchanger with DX Coil Unit only

0000: Invalid

Adjusting this setting is 

necessary for the header unit. 

(System equipped with the Air to 

Air Heat Exchanger with DX Coil 

Unit and air conditioners)

32

Remote controller 

sensor

0000: Do not use
0001: Use

0000: Do not use

48

Unbalanced 

ventilation Fan 

speed

0000: Normal
0001: SA (High) > EA (Low) active
0002: SA (Low) < EA (High) active
* “High” may be “Extra High”.

0000: Normal

Adjusting this setting is 

necessary for all the Air to Air 

Heat Exchanger with DX Coil 

Units in the group.

4C

Nighttime heat 

purge

0000: Invalid
0001-0048: Start after [Setting value] x 

1 hour(s)

* Setting for the time before the 

nighttime heat purge operation starts

0000: Nighttime 

heat purge 

OFF

Adjusting this setting is 

necessary for all the Air to Air 

Heat Exchanger with DX Coil 

Units in the group. (System 

equipped with the Air to Air Heat 

Exchanger with DX Coil Unit and 

air conditioners)

4E

Setting of the linked 

operation with 

external devices

0000: ON/OFF linked
0001: ON linked
0002: OFF linked
* Specifies whether the ON/OFF 

operation of the Air to Air Heat 

Exchanger with DX Coil Unit is linked 

with the external device operation

0000: ON/OFF 

linked

Adjusting this setting is 

necessary for a Air to Air Heat 

Exchanger with DX Coil Unit to 

which an adapter for remote ON/

OFF control (sold separately) is 

connected.

EA

Changing the 

ventilation mode

0002: Heat Exchange mode
0003: Automatic mode
* Compatible with systems without a 

remote controller and RBC-AMT32E

0003: Automatic 

mode

*1

EB

Changing the 

ventilation Fan 

speed

0002: High
0003: Low
0004: Unbalanced
* “High” may be “Extra High”.
* Compatible with systems without a 

remote controller and RBC-AMT32E

0002: High

*1

ED

Changing the 

operation output

0000: ON during normal operation
0001: ON during normal operation or 

nighttime heat purge operation

0002: ON during nighttime heat purge 

operation

0003: ON when SA fan is running
0004: ON when EA fan is running

0000: ON during 

normal 

operation

Adjusting this setting is 

necessary for a Air to Air Heat 

Exchanger with DX Coil Unit 

which transfers the operation 

output.

EE

Changing the 

abnormal signal / 

Bypass mode 

signal output

0000: ON when an abnormal signal is 

detected

0001: ON when the Bypass mode 

signal is detected

0000: ON when an 

abnormal 

signal is 

detected

Adjusting this setting is 

necessary for a Air to Air Heat 

Exchanger with DX Coil Unit 

which transfers the operation 

output.

Group control

In a group control, a remote controller can control up to maximum 8 units.
• For wiring procedure and wiring method of the individual line (Identical refrigerant line) system, refer to “Electric 

wiring” in this Manual.

• Wiring between indoor units in a group is performed in the following procedure.

Connect the indoor units by connecting the remote controller inter-unit wires from the remote controller terminal 
blocks (A/B) of the indoor unit connected with a remote controller to the remote controller terminal blocks (A/B) 
of the other indoor unit. (Non-polarity)

• For address setup, refer to the Installation Manual attached to the outdoor unit.

Changing the time before the Filter Sign lights up

The time before the Filter Sign lights up can be changed according to the installation conditions.
* Adjust this setting for the header unit.

• Select [01] in step 3 on page 70.
• Select a value from the table on the below in step 4 on page 70 according to the preferred time before the 

Filter Sign lights up.

For better heating performance

When it is hard to become hot due to the location of the indoor unit, room structure, etc., you can raise the detect 
temperature for heating. It is recommended that you use a circulator or the like to circulate warm air around the 
ceiling.

• Select [06] for CODE NO. in Step 3 on page 70.
• Select CODE NO. from the following table in Step 4 on page 70:

* In addition to the above detect temperature shift value, the own detect temperature shift value (Heat: 2.5 °C, 

Cool: -2.0 °C) is set for the Air to Air Heat Exchanger with DX coil unit in order to intake enough outdoor air. This 

setting does not need to be changed, but if you want to change the setting, contact our Customer Support Center.

Code

SET DATA

0000

0001

0002

0003

0004

01

Time before the Filter 

Sign lights up

None

150H

2500H

(Factory default)

5000H

10000H

Code

SET DATA

0000

0001

0002

0003

0004

0005

0006

06

Detect temperature 

Shift value

None

+ 1 °C

+ 2 °C

(default)

+ 3 °C

+ 4 °C

+ 5 °C

+ 6 °C

141-EN

142-EN

+00EH99887601-2_01EN.book  Page 71  Thursday, September 15, 2016  5:23 PM

Содержание MMD-VN1002HEX1E























































































Отзывы: