5
MMD-AP___1HF2UL
E15-3S2
0.7"(18)
2.3"(59)
Discharge temp sensor
Discharge
2.1"(52)
42.6"(1083) Outside
13.7"(347)
Outside
Z
2.6"(65)
2.6"×5=12.8"
(65×5=325)
0.4"(9)
2.6"(65)
1.1"
(28)
2.6"×5=12.8"
(65×5=325)
2.6"(66)
19.5"(496)
27.5"(699)
33.3"(845)
Drain pipe connection port(V25)
Taper screw for R1,1"(25.4) pipes
Screw hole for
duct mounting
(6-Ø0.2"(5))
Screw hole for duct mounting
(6-Ø0.2"(5))
1.9"
(49)
8.6"
(218)
5.9"
(150)
0.4"(10)
0.8"(20)
49.8"(1266)
0.7"(19)
0.4"(9)
Hole for hanging bolt
Refrigerant pipe connection port
(Liquid side Ø1/2"(12.7) Flared)
(4-Ø1/2"(12)×3.6"(92))
Suction
42.6"(1083) Outside
15.1"(383)
Outside
50.7"(1288) Mounting Location
52.3"(1328)
2.6"(65)
1.8"(45)
2.6"×16=40.9"(65×16=1040)
2.6"(65)
1.8"(45)
2.6"×16=40.9"(65×16=1040)
32.2"(818)
Mounting Location
55"(1398)
3.7"(93)
0.4"(9)
0.7"(19)
0.4"(9)
0.7"(19)
Screw hole for duct mounting(17-Ø0.2"(5))
Screw hole for duct mounting(17-Ø0.2"(5))
Refrigerant pipe connection port
(Gas side Ø7/8"(22.2) Brazed)
Access Area
23.6"
(600)
23.6"
(600)
Electrical box
Air flow
Space required for installation and servicing
Example
Access Area
23.6"(600)
Service space
Over
7.9"
(200)
Service space
7.9"
(200)
Over 39.4"(1000)
Outside Air Unit
Outside Air Unit
Flexible duct
Filter Box
Filter
Flexible duct
Ceiling
Air intake duct
Access Area
Outside air
Over
3.9"
(100)
Over
2.0"
(50)
4.0"(100)
6.6"(166)
1.3"
(33)
Ø1"(26) Hole for control wire
Ø7/8"(22.2) Hole for power supply cable
and remote control wiring
Z view
Installation Notice
1. Provide access area to the right of the unit as shown.
2. Condensate piping should slope downwards in the direction of
condensate flow,with a minimum gradient of 1in per 100 inches.
Condensate pipe should be insulated to avoid condensation.
3. Check condensate system for proper drainage before starting the unit.
4. Avoid installation of unit in Hazardous locations.
5. Filter and filter box are field provided and field installed items which
would prevent deposition of duct and dirt in the unit.
6. Install flexible duct for easy disassembly of the unit during major
service or breakdown.
7. Insulating the suction duct is recommended to avoid any
condensation on the exterior from untreated outside air.
8. Outside air louver with screen is recommended at the outside air
opening on the exterior wall.
Unit: in(mm)