manualshive.com logo in svg

Toshiba MCY-MHP0404HT, Руководство по обслуживанию, Страница: 98 / 184

Поделиться
Скачать
Toshiba MCY-MHP0404HT Скачать руководство пользователя страница 98

109

9-2. Troubleshooting method

The remote controllers (main remote controller and central control remote controller) and the interface P.C. board 

of an outdoor unit are provided with an LCD display (remote controller) or a 7-segment display (outdoor interface 

P.C. board) to display operational status. Using this self-diagnosis feature, the fault site / faulty part may be 

identified in the event of a fault by following the method described below.

The list below summarizes check codes detected by various devices. Analyze the check code according to where it is displayed and work out 

the nature of the fault in consultation with the list.

• When investigating a fault on the basis of a display provided on the indoor remote controller or TCC-LINK central control remote controller - 

See the “TCC-LINK remote controller or main remote controller display” section of the list.

• When investigating a fault on the basis of a display provided on an outdoor unit - See the “Outdoor 7-segment display” section of the list.

• When investigating a fault on the basis of a wireless remote controller-controlled indoor unit - See the “Light sensor indicator light block” 

section of the list.

List of Check Codes (Indoor Unit)

(Error detected by indoor unit)

Check code

Display of receiving unit

Typical fault site

Description of error

TCC-LINK 

central control 

or main remote 

controller 

display

Outdoor 7-segment display

Indicator light block

Sub-code

Flash

E03

–

–

Indoor-remote controller periodic 

communication error

Communication from remote controller or network adaptor 

has been lost (so has central control communication).

E04

–

–

Indoor-outdoor periodic communication 

error

Signals are not being received from outdoor unit.

E08

E08 Duplicated indoor address

Duplicated indoor address

Indoor unit detects address identical to its own.

E10

–

–

Indoor inter-MCU communication error MCU communication between main controller and motor 

microcontroller is faulty.

E18

–

–

Error in periodic communication 

between indoor header and follower 

unit

Periodic communication between indoor header and follower 

units cannot be maintained.

F01

–

–

ALT Indoor heat exchanger temperature 

sensor (TCJ) error

Heat exchanger temperature sensor (TCJ) has been open / 

short-circuited.

F02

–

–

ALT Indoor heat exchanger temperature 

sensor (TC2) error

Heat exchanger temperature sensor (TC2) has been open / 

short-circuited.

F03

–

–

ALT Indoor heat exchanger temperature 

sensor (TC1) error

Heat exchanger temperature sensor (TC1) has been open / 

short-circuited.

F10

–

–

ALT Ambient temperature sensor (TA) error Ambient temperature sensor (TA) has been open / short-

circuited.

F11

–

–

ALT Discharge temperature sensor (TF) 

error

Discharge temperature sensor (TF) has been open / short-

circuited.

F29

–

–

SIM P.C. board or other indoor error

Indoor EEPROM is abnormal (some other error may be 

detected).

L03

–

–

SIM Duplicated indoor group outdoor unit

There is more than one outdoor unit in group.

L07

–

–

SIM Connection of group control cable to 

stand-alone indoor unit

There is at least one stand-alone indoor unit to which group 

control cable is connected.

L08

L08

–

SIM Indoor group address not set

Address setting has not been performed for one or more 

indoor units (also detected at outdoor unit end).

L09

–

–

SIM Indoor capacity not set

Capacity setting has not been performed for indoor unit.

L20

–

–

SIM Duplicated central control address

There is duplication in central control address setting.

L30

L30 Detected indoor unit No.

SIM Indoor external error input (interlock)

Unit shutdown has been caused by external error input 

(CN80).

P01

–

–

ALT Indoor AC fan error

Indoor AC fan error is detected (activation of fan motor 

thermal relay).

P10

P10 Detected indoor unit No.

ALT Indoor overflow error

Float switch has been activated.

P12

–

–

ALT Indoor DC fan error

Indoor DC fan error (e.g. overcurrent or lock-up) is detected.

P31

–

–

ALT Other indoor unit error

Follower unit cannot be operated due to outdoor unit alarm 

(E03 / L03 / L07 / L08).

IPDU: Intelligent Power Drive Unit (Inverter P.C. board)

: Lighting,  : Flashing,  : Goes off

ALT: Flashing is alternately when there are two flashing LED

SIM: Simultaneous flashing when there are two flashing LED

Operation Timer Ready

– 14 –

Troubleshooting for Demand Unit

Demand

P.C. board

is failed.

Exchange of transformer,

exchange of Demand

P.C. board

Exchange of

Demand

P.C. board

Fuse

F100 is melted.

NO

NO

YES

Exchange of transformer,

exchange of Demand

P.C. board

YES

Exchange of transformer

YES

Short-circuit is

found between 1 and 2

pins of connector connected to

CN102 of

transformer.

Take off wiring of

CN102. Short-circuit is

found between “~” and

“~” of DB100.

NO

97

Содержание MCY-MHP0404HT

























































































































































































Отзывы:

Нет отзывов