manualshive.com logo in svg

Toshiba MCY-MHP0404HT, Руководство по обслуживанию, Страница: 157 / 184

Поделиться
Скачать
Toshiba MCY-MHP0404HT Скачать руководство пользователя страница 157

156

No. Component

Procedure

Remarks

⑤

Inverter 

assembly 

(continued)

5) Remove the terminal cover of the compressor, 

and disconnect the compressor leads from the 

compressor.

WARNING

The fast-on terminals of the compressor 

lead wires may become loose when they 

are disconnected. When reconnecting them, 

crimp them slightly with radio pliers or the 

like and ensure they are not loose before 

reinsertion. The fast-on terminals could 

overheat and cause a fire if loose.

6) Remove the screws of the inverter assembly 

and inverter fixing plate (lower). 

(M4×10, 1 )

7) Lift up on the inverter assembly and move it 

forward and out.

Inverter assembly

Inverter assembly

●Remove the inverter assembly.

Screw (1 position)

Thermostat

Compressor leads

Black

Red

Put on the

sleeve.

White

Notes on Compressor Leads

• Connect each compressor lead wire to its 

designated terminal.

• Do not press the fast-on terminals twice.

• After disconnecting the fast-on terminals that 

have been inserted once, replace the 

compressor leads.

• Make sure to keep the exposed compressor 

lead wires straight.

• Be careful not to apply excess stress to the 

terminals and lead wires.

• Attach the terminal cover after passing the 

lead wires through the bushing. At this time, be 

careful not to let the lead wires get caught in 

the gap with the terminal cover.

Screw (1 position)

Thermostat

Compressor leads

Black

Red

Put on the

sleeve.

White

Notes on Compressor Leads

• Connect each compressor lead wire to its 

designated terminal.

• Do not press the fast-on terminals twice.

• After disconnecting the fast-on terminals that 

have been inserted once, replace the 

compressor leads.

• Make sure to keep the exposed compressor 

lead wires straight.

• Be careful not to apply excess stress to the 

terminals and lead wires.

• Attach the terminal cover after passing the 

lead wires through the bushing. At this time, be 

careful not to let the lead wires get caught in 

the gap with the terminal cover.

Содержание MCY-MHP0404HT

























































































































































































Отзывы:

Нет отзывов