Toshiba MCY-MHP0404HT Скачать руководство пользователя страница 156

Страница: 156 / 184

155

No. Component

Procedure

Remarks

⑤

Inverter

assembly

WARNING

Do not detach the inverter for 5 minutes after

turning off the breaker as doing so may cause

electric shocks.

1. Detachment

1) Perform Step 1 of

①

, Step 1 of

②

, Step 1 of

③

and Step 1 of

④

2) Unplug the two fan motor lead connectors and

remove the cord clamps (1 position).

Remove the two metal bands, and disengage

the fan motor leads from the inverter fixing

plate (lower) hooks (2 positions).

CN700 ...Fan motor lead (3P: blue)

CN750 ...Fan motor lead (3P: white)

3) Unplug the connectors of the sensors

connected to other components on the

interface P.C. board.

CN502 ...TD sensor (3P: white)

CN507 ...TO sensor (2P: yellow)

CN520 ...TE sensor (2P: green)

CN505 ...TS sensor (2P: white)

CN523 ...TL sensor (2P: white)

CN317 ...4-way valve coil (3P: blue)

CN300 ...PMV coil (6P: white)

CN312 ...2-way valve coil (3P: red)

CN314 ...2-way valve coil (4P: white)

CN311 ....2-way valve coil (3P: white)

CN308 ...Thermostat (2P: red)

CN501 ...High-pressure sensor (4P: red)

CN500 ...Low-pressure sensor (4P: white)

CN600 ...Connection with 2 fan IPDU P.C. board (CN504) (5P: blue)

CN400 ...Connection with noise filter P.C. board (CN08) (3P: white)

4) Remove the sensor lead wire clamp

(2 positions).

CAUTION

Disengage the locks on the housing to unplug

the connectors.

Lead wire clamp

of fan motor

(1 position)

Metal bands (2 each)

Inverter fixing plate (lower) hooks

(2 positions)

Sensor lead wire
clamps
(2 positions)

Fan motor connectors

(2 positions)

Notes

• Insert the connector of fan

lead of the upper part in

CN700 (3P: blue).

Содержание MCY-MHP0404HT

























































































































































































Результаты поиска

Содержание MCY-MHP0404HT

Отзывы:

Toshiba MCY-MHP0404HT, Руководство по обслуживанию, Страница: 156 / 184

Результаты поиска

Содержание MCY-MHP0404HT

Отзывы: