Toshiba MCY-MHP0404HT Скачать руководство пользователя страница 114

Страница: 114 / 184

124

I/F

All stop

• Check for defect in outdoor

P.C. board (A3-IPDU).

• Check for defect in outdoor

power supply wiring.

P07

–

IPDU

I/F

Heat sink

overheating

error

All stop

Temperature sensor built into

IGBT (TH) is overheated.

• Check power supply

voltage.

• Check outdoor fan system

error.

• Check heat sink cooling

duct for clogging.

• Check IGBT and heat sink

for thermal performance for

faulty installation.

(e.g. mounting screws and

thermal conductivity)

• Check for defect in A3-

IPDU.

(faulty IGBT built-in

temperature sensor (TH))

P10

Detected

indoor address

Indoor

unit

Indoor overflow

error

All stop

• Float switch operates.

• Float switch circuit is open-

circuited or disconnected

at connector.

• Check float switch

connector.

• Check operation of drain

pump.

• Check drain pump circuit.

• Check drain pipe for

clogging.

• Check for defect in indoor

P.C. board.

P12

–

Indoor

unit

Indoor fan motor

error

Stop of

corresponding

unit

• Motor speed

measurements

continuously deviate from

target value.

• Overcurrent protection is

activated.

• Check connection of fan

connector and wiring.

• Check for defect in fan

motor.

• Check for defect in indoor

P.C. board.

• Check impact of outside air

treatment (OA).

P13

–

I/F

Outdoor liquid

backflow

detection error

All stop

• Check full-close operation

of outdoor PMV.

• Check for defect in Pd or

Ps sensor.

• Check defect in outdoor

P.C. board (I/F).

• Check capillary of oil

separator oil return circuit

for clogging.

• Check for leakage of check

valve in discharge pipe

convergent section.

Location

detection

Description

System status

Error detection

condition(s)

Check items (locations)

Main

remote

controller

Outdoor 7-segment display

Check

code

Sub-code

• Check gas balancing

circuit (SV2) for clogging.

Check code

–

Inverter DC

voltage (Vdc)

error

(compressor)

• Inverter DC voltage is too

high (overvoltage) or too

low (undervoltage).

When system is in heating

operation, outdoor PMV 1

continuously registers

opening of 100 p or less while

under SH control.

P05

113

Содержание MCY-MHP0404HT

























































































































































































Результаты поиска

Содержание MCY-MHP0404HT

Отзывы:

Toshiba MCY-MHP0404HT, Руководство по обслуживанию, Страница: 114 / 184

Результаты поиска

Содержание MCY-MHP0404HT

Отзывы: