Toshiba IK-VR01A Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 19

background image

- 4 -

4. PART NAMES & FUNCTIONS

LL

ON

OFF

BLC

Mode Setting Switch

BLC (Backlight Compensation Switch)
With the switch on, it adjusts
the backlight automatically to
obtain the best possible image.
LL
Sets camera synchronization
to line lock with the switch on.
Available only with AC24V.

Lens Iris ADJ

Monitor Out Connector

Connect with the supplied monitor out
harness wire. Used to adjust the angle of
view when installing the camera.

Line Lock Phase ADJ

Counterclockwise: The picture becomes
darker.
Clockwise: The picture becomes
brighter.
"Optimum Value" is at default setting.

Adjusts the phase of the line lock.

«
...
3
4
5
6
7
...
»

Содержание IK-VR01A




















Отзывы:

Нет отзывов

Похожие инструкции для IK-VR01A

MyDlink DCH-S150

Бренд: D-Link Страницы: 8

Бренд: Panasonic Страницы: 42

Бренд: Aigis Mechtronics Страницы: 20

Бренд: 3xLogic Страницы: 16

iDS-2CD6124FWD-B

Бренд: HIKVISION Страницы: 29

Бренд: Bogen Страницы: 2

Бренд: Hiltron Страницы: 64

Бренд: Trailer Vision Страницы: 18

Бренд: Axis Страницы: 32

Бренд: Ideal Security Страницы: 4

Бренд: Axis Страницы: 42

Calibration Pro

Бренд: Buckleys Страницы: 12

STI-6400 Exit Stopper

Бренд: Safety Technology International Страницы: 7

Бренд: SVBONY Страницы: 41

Бренд: urmet domus Страницы: 8

Бренд: DELTA DORE Страницы: 2

VER. 061030 CAM-6500

Бренд: ACTi Страницы: 13

Бренд: Argo Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды