background image

- 3 -

1. FEATURES & DESCRIPTION

IK-VR01A has the following features:
(1) Flush/Surface mount.
(2) IP66 Standard for dust and water resistance.
(3) Built in vari-focal lens with auto-iris

Focal length 3.0~8.0mm.

(4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent

sensitivity
480 lines horizontal resolution
0.4 lx minimum illumination with tint dome cover

(5) 50dB Signal-To Noise Ratio
(6) Power supply- AC24V or DC12V - This camera automatically detects the power.
(7) BLC, AGC, and Line-Lock (AC24V)

2. CAUTIONS

(1) Avoid touching the lens glass with your fingers. If necessary, use a soft cloth

moistened with alcohol to wipe off any dust.

(2) Avoid aiming the camera at the sun.
(3) Avoid shooting the camera at intense light. Intense light such as a spotlight may

cause a bloom or smear. A vertical stripe may appear on the screen.
However, this is not a malfunction.

(4) Install the camera away from video noise. If cables are wired near electric lighting

wires or a TV set, noise may appear in images. In this event, relocate cables or
reinstall equipment.

3. COMPONENTS

(1) Camera (with Tint Dome Cover installed)

1 pc.

(2) Accessories

(a) Mounting Base

1 pc.

(b) Bracket

1 pc.

(c) Screw A

3 pcs.

(d) Screw B

3 pcs.

(e) Clear Dome Cover

1 pc.

(f)

Special Hexangular Wrench

1 pc.

(g) Monitor Out Harness Wire

1 pc.

(h) Power Connector

1 pc.

(i)

Instruction Manual

1 pc.

Содержание IK-VR01A




















Отзывы: