Toshiba IK-VR01A Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 19

background image

- 13 -

9. IN CASE OF PROBLEMS

Condition

No image

Unnatural color

The image is out of
focus.
The image is dark.

Check Points

• Are the camera and connected equipment turned on?
• Are cables connected correctly?
• Is the monitor TV adjusted correctly?
• Is the lighting too weak?
• Is the lens focus adjusted?
• Is the lens or cover dirty?
• Are there any large barrier or bright illumination near the

camera?

• Is the lens iris adjustment volume correctly set?

«
...
12
13
14
15
16
...
»

Содержание IK-VR01A




















Отзывы:

Нет отзывов

Похожие инструкции для IK-VR01A

EF35mm f/2 IS USM

Бренд: Canon Страницы: 2

EF300mm f/2.8L IS II USM

Бренд: Canon Страницы: 13

EF28-135mm f/3.5-5.6 IS USM

Бренд: Canon Страницы: 9

Бренд: AccuBANKER Страницы: 2

Бренд: D3D Страницы: 4

Бренд: Samsung Страницы: 1

iPOLiS SNP-3120

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 7

Бренд: Samsung Страницы: 23

iPOLiS SNP-3120

Бренд: Samsung Страницы: 2

iPolis SNO-5080R

Бренд: Samsung Страницы: 60

GO!control 2GIG-CNTRL2

Бренд: 2gig Technologies Страницы: 52

GO!control 2GIG-CNTRL2

Бренд: 2gig Technologies Страницы: 52

Бренд: D-MAX Страницы: 33

MagnaLatch ALERT

Бренд: D&D Technologies Страницы: 2

Бренд: Tamron Страницы: 9

Бренд: WATERGUARD Страницы: 2

Бренд: IDS Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды