background image

- 11 -

10. SPECIFICATIONS

1. Image System

Image Device
Pixel Elements

2. Electrical

TV System

Horizontal Resolution
S/N Ratio
Minimum Illumination

Auto Gain Control (AGC)
Iris Control Mode
White Balance
White Balance Range
Line lock Vertical phase adjustment

γ

 compensation

Backlight Compensation (BLC)
Video Output Signal
Synchronizaiton System

3. Mechanical

Weight
Dimension

4. Optical

Built-in Lens

View Angle

Focus Length

5. Power

Input Voltage
Power Consumption

6. Environmental

Operating Temperature
Storage Temperature

7. Regulation

Safety
Emission

1/4” IT CCD
768 (H) x 494 (V)

2:1 Interlace, 15.734KHz Horizontal, 59.94Hz
Vertical
480 TV lines
50dB (TYP. AGC Off, Weight On)
0.2 lux (More than 10% of image output, Clear cover)
0.5 lux (More than 10% of image output, Smoke cover)
Average AGC (24dB)
Auto Iris Lens
Auto
2500

°

K ~ 10000

°

K

Provided (VR : range 300deg)
0.45
On / Off (DIP-SW)
VBS (1.0Vp-p, 75ohm unbalance, BNC)
Internal for DC or Linelock for AC

290g
110mm (

φ

) x 96mm (H)

Vari-focus Lens
f=2.8 ~ 5.8mm, F1.4 : Auto Iris
Wide : 97.5

°

 (D), 76.7

°

 (H), 56.8

°

 (V)

Tele : 47.9

°

 (D), 38.2

°

 (H), 28.7

°

 (V)

0.2m ~ 

DC12V or AC24V
3.5W

-10

°

C~50

°

C 90%RH max

-20

°

C~60

°

C 70%RH max

UL2044
FCC Class A / DOC ClassA

Содержание IK-DF01A

















Отзывы: