background image

 

Installation Notes

  

ƒ

 

The drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid 
excessive distortion.  

ƒ

 

In order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be 
kept under the PCB.  

ƒ

 

Space should be kept around the drive to avoid any contact with other parts, which may occur 
due to shock or vibration.  

ƒ

 

The temperature of the top cover and the base must always be kept under 60C to maintain the 
required reliability.  

ƒ

 

Be sure not to cover the breathing hole to keep the pressure inside the drive at a certain level  

ƒ

 

Do not apply any force to the top cover, except the screw areas on top cover. Maximum force to 
the specified area is 2N.  

ƒ

 

The drive contains several parts which may be easily damaged by ESD (Electric Static 
Discharge). Avoid touching the interface connector pins and the surface of PCB. Be sure to use 
ESD proof wrist strap when handling drive.  

ƒ

 

The four mounting screws should be tightened equally with 0.3N-m (3kgf-cm) torque. The depth 
should be 3.0mm minimum and 3.5mm maximum.  

Placing Hard Drive inside your Computer

   

 

Determine mounting configuration (the drive can be mounted in either a horizontal or vertical 
orientation)  

 

Configure drive for system application.  

 

Configure the adapter board for the specific system application (if required).  

 

Install adapter board into an unused PC/AT 16 bit slot (if required).  

 

Install the I/F cable to the system's 44 pin connector port or adapter board. Ensure pin 1 is 
oriented correctly, (pin 1 on the cable is usually identified by a red or blue strip.)  

 

Set correct drive type in system CMOS  

 

Refer to applicable manuals for software installation instructions.  

 

 

Important Note: Disconnect power from your computer system before beginning installation. 

 

 

Figure 2.HDD Mounting H

oles 

Содержание HDD2158












Отзывы: