manualshive.com logo in svg

Toshiba GX9 ASD, Быстрый старт

Поделиться
Скачать
Toshiba GX9 ASD Скачать руководство пользователя страница 7

About This Guide

This guide was written by the Toshiba International Corporation Technical Publications Group. This 
group is tasked with providing technical documentation for the 

GX9 Adjustable Speed Drive

. Every 

effort has been made to provide accurate and concise information to you, our customer.

At Toshiba International Corporation we are continuously striving for better ways to meet the constantly 
changing needs of our customers. E-mail your comments, questions, or concerns about this publication 
to 

[email protected]

.

Guide’s Purpose and Scope

This guide provides information on how to safely install, operate, maintain, and dispose of your 

GX9 Adjustable Speed Drive

. The information provided in this guide is applicable to the 

GX9 Adjustable Speed Drive

 only.

This guide provides information on the various features and functions of this powerful cost-saving 
device, including

•

Installation,

•

System operation,

•

Configuration and menu options, and

•

Mechanical and electrical specifications.

Included is a section on general safety instructions that describe the warning labels and symbols that are 
used on the device and throughout the guide. Read the guide completely before installing, operating, 
performing maintenance, or disposing of this equipment.

This guide and the accompanying drawings should be considered a permanent part of the equipment 
and should be readily available for reference and review. Dimensions shown in the guide are in English 
and/or the metric equivalent.

Because of our commitment to continuous improvement, Toshiba International Corporation reserves the 
right, without prior notice, to update information, make product changes, or to discontinue any product 
or service identified in this publication.

Toshiba International Corporation 

(TIC)

 shall not be liable for direct, indirect, special, or 

consequential damages resulting from the use of the information contained within this guide.

This guide is copyrighted. No part of this guide may be photocopied or reproduced in any form without 
the prior written consent of Toshiba International Corporation.

© Copyright 2014 Toshiba International Corporation.

TOSHIBA

® is a registered trademark of Toshiba Corporation. All other product or trade references 

appearing in this guide are registered trademarks of their respective owners.

All rights reserved.

Printed in the U.S.A.

Содержание GX9 ASD





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды